Performance Testing of Trenchless Wastewater Line Spot Repairs
Publication: Journal of Infrastructure Systems
Volume 3, Issue 1
Abstract
The University of Texas at Austin conducted a study for the City of Austin to evaluate the performance of commercially available trenchless spot-repair methods in the City's wastewater pipelines. This paper reports short-term testing procedures and results for two epoxy resin repair methods that were a part of the study. Both methods of repair were proposed by the City of Austin Department of Water and Wastewater, and were field demonstrated in Austin on 200-mm (8-in.) unreinforced concrete wastewater lines. Each process uses remote control, cured-in-place techniques: one method employs a robot to prepare substrate surfaces and to inject epoxy into pipe defects; the other employs an inflatable rubber packer to form a continuous epoxy collar up to 0.6 m in length at the defect. The objective of the study was to evaluate and compare, by field sampling and laboratory testing, the structural integrity and watertightness of the repair processes. A small number of repair samples were obtained by excavation of actual damaged pipe repaired by each method. Tests of the repaired pipe yielded results for bond strength and watertightness of the repair, which differ sharply between the two methods. Possible causes of bond failure are discussed.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Allan, R., and Edwards, S. (1993). The repair of concrete structures, 2nd Ed., Blackie Academic & Professional, Glasgow, Scotland.
2.
Bauhan, T. (1994). “Independent evaluation of sewer repair techniques for the Upper Waller Creek Basin rehabilitation project: material assessment,” MS thesis, University of Texas at Austin, Austin, Tex.
3.
Emmons, P. (1993). Concrete repair and maintenance illustrated. R. S. Means Co., Kingston, Mass.
4.
Gray, W. W. S. (1996). “Trenchless technology for sewer rehabilitation.”Civil Engineering News, (March).
5.
Iseley, D. T., and Mohammad, N. (1992). “Trenchless pipeline rehabilitation.”Constructor (October).
6.
Knab, L., Sprinkel, M., and Lane, O. (1989). “Preliminary performance criteria for the bond of portland cement and latex modified concrete overlays.”NISTIR 89-4156, National Institute of Standards and Technology, Gaithersburg, Md.
7.
Patty, T. (1994). “Petrographic and chemical studies of City of Austin concrete wastewater pipe for the University of Texas at Austin.” Erlin Hime Associates, Austin, Tex.
8.
Schrock, B. J. (1992). “Pipeline rehabilitation: a guide to a growing market.”The National Utility Contractor, NUCA (August).
9.
Sewer rehabilitation, a manual of practices. (1991). Water Pollution Control Federation, Alexandria, Va.
10.
Standard test method for pull-off strength of coatings using portable adhesion testers; ASTM D4541-93. (1993). ASTM, Philadelphia, Pa.
11.
Stark, E. (1994a). “Epoxy resins for use in pipe rehabilitation: an overview.”Proc., North Am. No-Dig Conf., North American Society for Trenchless Technology, Chicago, Ill.
12.
Stark, E. (1994b). Personal communication with the author. (April).
13.
Stein, D. (1992). “Determining ultimate load values for cracked pipes repaired with a robot.” Ruhr University, Bochum, Germany.
14.
Wright, C. W. (1994). “Rehabilitation of sanitary sewers in the City of Austin,” MS thesis, University of Texas at Austin, Austin, Tex.
Information & Authors
Information
Published In
Copyright
Copyright © 1997 American Society of Civil Engineers.
History
Published online: Mar 1, 1997
Published in print: Mar 1997
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.