Shear Transfer across a Crack in Reinforced High-Strength Concrete
Publication: Journal of Materials in Civil Engineering
Volume 20, Issue 4
Abstract
In this study, the shear transfer behavior of reinforced concrete across a crack is investigated both analytically and experimentally by conducting tests on 19 precracked push-off specimens. The major parameters considered are the compressive strength of concrete and reinforcement parameter through the shear plane. Test results indicate that the behavior of a crack (in terms of stress-displacement relations) during shear transfer is characterized by four significant events. The mechanisms involved in each of these events are described. It has been shown that an independent increase either in concrete strength or reinforcement parameter stiffens the initial (after taking off the slack created by the precrack) straight portion of the curve, raises the linear response to a higher load level and increases the ultimate strength and the corresponding deformation, but the slope of the branch where frictional slip occurs remains relatively unchanged. A large pool of test data on reinforced concrete has been collated from the available literature. These, together with the test data generated in this study, have been analyzed and modeled embracing concrete strength up to about for predicting the ultimate shear transfer strength across a crack. A comparison of theoretical predictions with available test results shows good agreement.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The research reported herein was partly supported by Research Grant No. UNSPECIFIEDR-264-000-015-112 with funds given by the National University of Singapore.
References
Ali, M. A., and White, R. N. (1999). “Enhanced contact model for shear friction of normal and high-strength concrete.” ACI Struct. J., 96(3), 348–360.
American Concrete Institute (ACI). (2005). “Building code requirements for structural concrete.” No. 318-2005, Committee 318, Farmington Hills, Mich.
Birkeland, P. W., and Birkeland, H. W. (1966). “Connections in precast concrete construction.” J. Am. Concr. Inst., 63(3), 345–368.
Dulacska, H. (1972). “Dowel action of reinforcement crossing the cracks in concrete.” ACI J., 9(12), 754–757.
Hsu, T. T. C., Mau, S. T., and Chen, B. (1987). “Theory of shear transfer strength of reinforced concrete.” ACI Struct. J. 84(2), 149–160.
Lin, I. J., and Chen, Y. L. (1989). “Shear transfer across a crack in reinforced high strength concrete.” Proc., 2nd East Asia-Pacific Conf. on Structural Engineering, and Construction, Chiang Mai, Thailand, 85–91.
Loov, R., and Patnaik, A. (1994). “Horizontal shear strength of composite concrete beams with rough interface.” PCI J., 39(1), 48–67.
Mast, R. F. (1968). “Auxiliary reinforcement in concrete connections.” J. Struct. Div., 94(ST 6), 1485–1504.
Mattock, A. H. (1974). “Shear transfer in concrete having reinforcement at an angle to the shear plane.” Shear in reinforced concrete, Vol. 1, ACI SP-42, 17–42.
Mattock, A. H. (1976). “Shear transfer under monotonic loading across an interface between concrete cast at different times.” Report SM 76-3, Dept. of Civil Engineering, Univ. of Washington, Seattle, Wash.
Mattock, A. H. (2001). “Shear friction and high-strength concrete.” ACI Struct. J., 98(1), 50–59.
Mattock, A. H., and Hawkins, N. M. (1972). “Research on shear transfer in reinforced concrete.” J. Prestressed Concr. Inst., 17(2), 55–75.
Mau, S. T., and Hsu, T. T. C. (1988). “Discussion on ‘Influence of concrete strength and loading history on the shear friction capacity of concrete members.’” PCI J., 33(1), 166–170.
Nielsen, M. P. (1998). Limit analysis and concrete plasticity, 2nd Ed., CRC, Boca Raton, Fla.
Prestressed Concrete Institute (PCI). (1992). PCI design handbook, 4th Ed., PCI, Chicago.
Vinayagam, T. (2004). “Shear transfer in high strength concrete.” Ph.D. thesis, Dept. of Civil Engineering, National Univ. of Singapore.
Walraven, J. C. (1981). “Fundamental analysis of aggregate interlock.” J. Struct. Div., 107(11), 2245–2270.
Walraven, J. C., Frenay, J., and Pruijssers, A. (1987). “Influence of concrete strength and load history on the shear friction capacity of concrete members.” PCI J., 32(1), 66–84.
Walraven, J. C., and Stroband, J. (1994). “Shear friction in high strength concrete.” Proc., ACI Int. Conf. on High Performance Concrete, Singapore, 311–330.
Weiss, R. (1978). “Ein haufwerkstheoretisches model der restfestigkeit grschädigter betone.” MS thesis, Technical Univ. of Braunschweig, Germany (in German).
Information & Authors
Information
Published In
Copyright
© 2008 ASCE.
History
Received: Mar 27, 2006
Accepted: Nov 27, 2006
Published online: Apr 1, 2008
Published in print: Apr 2008
Notes
Note. Associate Editor: Zhishen Wu
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.