Assessment and Repair of Fire-Damaged High-Strength Concrete: Strength and Durability
Publication: Journal of Materials in Civil Engineering
Volume 19, Issue 6
Abstract
Strength and durability are two key factors influencing the safety and service life of fire-damaged concrete structures. To develop an assessment method for fire-damaged high-strength concrete (HSC) structures that is convenient for postfire repair, the effects of concrete strength and aggregate type on the postfire residual compressive strength of HSC were studied in this paper. Subsequently, the changes in durability and microstructures were investigated by the rapid chloride-ion penetrability test, the mercury intrusion porosimetry test, and scanning electron microscopy observation, respectively. Based on the test results and further analysis, estimation of the temperature distribution in the fire-damaged concrete element is established by the dichotomy and mercury intrusion porosimetry test and scanning electron microscopy observation. According to the estimated temperature distribution, the postfire residual compressive strength can be assessed by the strip method and postfire durability can be assessed by the “two-level” method, respectively. Based on the assessments, the repair method for fire-damaged HSC structures is recommended in steps.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was supported by the research project “Spalling of High-Strength Concrete under Fire-Quantification and Prevention” (A/C Code: A-PD50) from the Hong Kong Polytechnic University, the National Key Technologies R&D Program “Researches on Durability and Disaster Prevention of HPC Residence” (2002BA806B-4), and Key Subject Construction in Shanghai.
References
ASTM. (1994). “Standard test method for electrical indication of concrete’s ability to resist chloride ion penetration.” C 1202-94, West Conshohocken, Pa.
ASTM. (2005a). “Standard specification for blended hydraulic cements.” C 595-05, West Conshohocken, Pa.
ASTM. (2005b). “Standard specification for portland cement.” C 150-05, West Conshohocken, Pa.
British Standards Institution (BSI). (1983a). “Method for determination of compressive strength of concrete cubes.” BS 1881-116, London.
British Standards Institution (BSI). (1983b). “Method for determination of water absorption.” BS 1881-122, London.
British Standards Institution (BSI). (1987). “Method for determination of the fire resistance of elements of construction.” BS 476-20, London.
British Standards Institution (BSI). (1992). “Porosity and pore size distribution of materials—Method of evaluation by mercury porosimetry.” BS 7591-1, London.
British Standards Institution (BSI). (1996). “Recommendations for the determination of the initial surface absorption of concrete.” BS 1881-208, London.
Castillo, C., and Durrani, A. J. (1990). “Effect of transient high temperature on high-strength concrete.” ACI Mater. J., 87(1), 47–53.
Chan, Y. N., Luo, X., and Sun, W. (2000). “Compressive strength and pore structure of high-performance concrete after exposure to high temperature up to .” Cem. Concr. Res., 30(2), 247–251.
Chan, Y. N., Peng, G. F., and Anson, M. (1999). “Residual strength and pore structure of high-strength concrete and normal-strength concrete after exposed to high temperatures.” Cem. Concr. Compos., 21(1), 23–27.
Cioni, P., Croce, P., and Salvatore, W. (2001). “Assessing fire damage to RC elements.” Fire Saf. J., 36(2), 181–199.
Felicetti, R., and Gambarova, P. G. (1998). “Effects of high temperature on the residual compressive strength of high-strength siliceous concretes.” ACI Mater. J., 95(4), 395–406.
Janotka, I., and Bagel, L. (2002). “Pore structures, permeabilities, and compressive strength of concrete at temperatures up to .” ACI Mater. J., 99(2), 196–200.
Kumar, R., and Bhattacharjee, B. (2003). “Porosity, pore size distribution and in situ strength of concrete.” Cem. Concr. Res., 33(1), 155–164.
Lin, C. H., Chen, S. T., and Yang, C. A. (1995). “Repair of fire-damaged reinforced concrete columns.” ACI Struct. J., 92(4), 406–411.
Luo, X., Sun, W., and Chan, S. Y. N. (2000). “Effect of heating and cooling regimes on residual strength and microstructure of normal strength and high-performance concrete.” Cem. Concr. Res., 30(3), 379–383.
Phan, L. T., and Carino, N. J. (2002). “Effects of test conditions and mixture proportions on behavior of high-strength concrete exposed to high temperatures.” ACI Mater. J., 99(1), 54–66.
Phan, L. T., Lawson, J. R., and Davis, F. L. (2001). “Effects of elevated temperature exposure on heating characteristics, spalling, and residual properties of high performance concrete.” Mater. Struct., 34, 83–91.
Poon, C. S., Azhar, S., Anson, M., and Wong, Y. L. (2001a). “Comparison of the strength and durability performance of normal- and high-strength pozzolanic concretes at elevated temperatures.” Cem. Concr. Res., 31(9), 1291–1300.
Poon, C. S., Azhar, S., Anson, M., and Wong, Y. L. (2001b). “Strength and durability recovery of fire-damaged concrete after post-fire-curing.” Cem. Concr. Res., 31(9), 1307–1318.
Wu, B., Su, X. P., Li, H., and Yuan, L. (2002). “Effect of high temperature on residual mechanical properties of confined and unconfined high-strength concrete.” ACI Mater. J., 99(4), 399–407.
Information & Authors
Information
Published In
Copyright
© 2007 ASCE.
History
Received: May 16, 2005
Accepted: Jul 14, 2006
Published online: Jun 1, 2007
Published in print: Jun 2007
Notes
Note. Associate Editor: Zhishen Wu
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.