Development of Mix Design Procedure for Cold In-Place Recycling with Foamed Asphalt
Publication: Journal of Materials in Civil Engineering
Volume 18, Issue 1
Abstract
The main objective of this study is to determine mix design parameters for cold in-place recycling with foamed asphalt. First, the foaming process of laboratory foaming equipment was validated by varying the water and asphalt content. 1.3% water content was adopted to create the optimum foaming characteristics in terms of the expansion ratio and the half-life at 170°C under air pressure of 400 kPa and water pressure of 500 kPa. The mix design was then performed using both the indirect tensile test and the Marshall test for 13 combinations of foamed asphalt content and water content for three different gradations. The water content did not appear to affect the test results significantly. Maximum stability (both wet and dry samples), maximum bulk density, and indirect tensile strength (both wet and dry samples) were all obtained around 2.5% foamed asphalt content. Overall, the highest Marshall stability and indirect tensile strength were obtained in the order of fine, field, and coarse reclaimed asphalt pavement gradations. It is recommended that the indirect tensile strength based on wet samples be adopted for determining the optimum foamed asphalt content.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers would like to thank the Iowa Highway Research Board (IHRB) for financial support and the members of the steering committee for their guidance throughout the project. The opinions, findings, and conclusions expressed in this publication are those of the writers and not necessarily those of the Iowa Department of Transportation.
References
Acott, S. M. (1979). “Sand stabilization using foamed bitumen.” Proc., 3rd Conf. on Asphalt Pavements for South Africa, Durban, 155–172.
AIPCR and PIARC. (2002). “Cold in-place recycling of pavements with emulsion or foamed bitumen.” Association Mondiale de la Route (AIPCR) and World Road Association (PIARC) Draft Report, Version 3.1A.
Akeroyd, F. M., and Hicks, B. J. (1988). “Foamed bitumen road recycling.” Highways (London), 56(1993), 42–45.
Asphalt Recycling and Reclaiming Association. (2001). Basic Asphalt Recycling Manual, Annapolis, 143–156
Bissada, A. F. (1987). “Structural response of foamed-asphalt-sand mixtures in hot environments.” Transportation Research Record 1115, Transportation Research Board, Washington, D.C., 134–149.
Bowering, R. H. (1970). “Properties and behaviors of foamed bitumen mixtures for road building.” Proc., 5th ARRB Conf., Australian Road Research Board, Canberra, 6, 38–57.
Bowering, R. H. (1976). “Foamed bitumen production and application of mixtures evaluation and performance of pavements.” Asph. Paving Technol., 24, 453–477.
Brennen, M., Tia, M., Altschaeffl, M., and Wood, L. E. (1983). “Laboratory investigation of the use of foamed asphalt for recycled bituminous pavements.” Transportation Research Record 911, Transportation Research Board, Washington, D.C., 80–87.
Castedo, F. L. H., and Wood, L. E. (1983). “Stabilization with foamed asphalt of aggregates commonly used in low-volume roads.” Transportation Research Record 898, Transportation Research Board, Washington, D.C., 297–302.
Csanyi, L. H. (1960). “Bituminous mixes prepared with foamed asphalt.” Iowa Engineering Experiment Station Bulletin No. 189, Iowa State Univ., Ames, Iowa.
Engelbrecht, J. C., Roberts, F. L., and Kennedy, T. W. (1985). “Cold recycled mixtures, with emphasis on the curing of foamed specimens—A laboratory study.” Proc., Annual Transportation Convention, Pretoria.
Lancaster, J., McArthur, S., and Warwick, R. (1994). “VICROADS experience with foamed bitumen stabilization.” Proc., 17th ARRB Conf., Australian Road Research Board, Gold Coast, 17(3), 193–211
Lee, D. Y. (1981). “Treating marginal aggregates and soil with foamed asphalt.” Proc. Association of Asphalt Paving Technologists, White Bear Lake, 50, 211–250.
Maccarrone. S., Holleran, G., Leonard, D. J., and Hey, S. (1994). “Pavement recycling using foamed asphalt.” Proc., 17th ARRB Conf. Australian Road Research Board, Gold Coast, 17(3), 349–365
Marquis, B., et al. (2003). “Design, construction and early performance of foamed asphalt full depth reclaimed (FDR) pavement in Maine.” Proc., TRB 82nd Annual Meeting (CD-Rom), Washington, D.C.
Mohammad, L. N., Abu-Farsakh, M. Y., Wu, Z., and Abadie, C. (2003). “Louisiana experience with foamed recycled asphalt pavement base materials.” Proc., TRB 82nd Annual Meeting (CD-Rom), Washington, D.C.
Murphy, D. T., and Emery, J. J. (1996). “Modified coild-in place asphalt recycling.” Transportation Research Record 1545, Washington, D.C.
Muthen, K. M. (1999). “Foamed asphalt mixes—Mix design procedure.” Contract Rep. No.CR-98/077, CSIR Transportek, South Africa.
Nataatmadja, A. (2001). “Some characteristics of foamed bitumen mixes.” Transportation Research Record 1767, Transportation Research Board, Washington, D.C., 120–125.
Roberts, F. L., Engelbrecht, J. C., and Kennedy, T. W. (1984). “Evaluation of recycled mixtures using foamed asphalt.” Transportation Research Record 968, Transportation Research Board, Washington, D.C., 78–85.
Ruckel, P. J., Kole, L. L., Abel, L., Zator, R. E., Button, J. W., and Epps, J. A. (1982). “Asphalt pavement construction: New Materials and techniques.” ASTM STP 724, West Conshohocken, Pa., 93–109.
Ruckel, P. J., Scott, S. M., and Bowering, R. H. (1980). “Foamed-asphalt paving mixtures: Preparation of design mixes and treatment of test specimens.” Transportation Research Record 911, Transportation Research Board, Washington, D.C., 88–95.
Sakr, H. A., and Manke, P. G. (1985). “Innovations in Oklahoma foam mix design procedures.” Transportation Research Record 1034, Transportation Research Board, Washington, D.C., 26–34.
Saleh. M. F. (2003). “New Zealand experience with foam bitumen stabilization.” Proc., TRB 82nd Annual Meeting (CD-Rom), Washington. D.C.
Tia, M., and Wood, L. E. (1983). “Use of asphalt emulsion and foamed asphalt in cold-recycled asphalt paving mixtures.” Transportation Research Record 898, Transportation Research Board, Washington, D.C., 315–321.
Van Wijk, A. (1984). “Structural comparison of two cold recycled pavement layers.” Transportation Research Record 954, Transportation Research Board, Washington, D.C., 70–77.
Van Wijk, A., and Wood, L. E. (1982). “Construction of a recycled bituminous pavement using foamed asphalt.” Proc. Canadian Technical Asphalt Association Meeting, Canadian Technical Asphalt Association, Edmonton.
Van Wijk, A., and Wood, L. E. (1983). “Use of foamed asphalt in recycling of an asphalt pavement.” Transportation Research Record 911, Transportation Research Board, Washington, D.C.
Van Wijk, A., Yoder, E. J., and Wood, L. E. (1983). “Determination of structural equivalency factors of recycled layers by using field data.” Transportation Research Record 898, Transportation Research Board, Washington, D.C., 122–132.
Information & Authors
Information
Published In
Copyright
© 2006 ASCE.
History
Received: May 10, 2004
Accepted: May 10, 2005
Published online: Feb 1, 2006
Published in print: Feb 2006
Notes
Note. Associate Editor: Eyad Masad
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.