Effect of Source of Fly Ash on Abrasion Resistance of Concrete
Publication: Journal of Materials in Civil Engineering
Volume 14, Issue 5
Abstract
This investigation was performed to establish the effects of the source and amount of fly ash on abrasion resistance of concrete. A reference concrete was proportioned to have a 28-day age strength of 41 MPa. Three sources of Class C fly ash were used in this research. From each source, three levels of fly ash to total cementitious materials content (40, 50, and 60%) were used in producing the concrete mixtures. The water to cementitious materials ratio was kept constant at 0.30 for all mixtures. An accelerated abrasion testing method, a modified ASTM C 944 test, was used to measure the abrasion resistance of this high-strength concrete. The effects of both the source and the amount of fly ash on abrasion resistance of concrete were noticeable. All concrete mixtures with and without fly ash exhibited high abrasion resistance in accordance with the ASTM requirement. Concrete abrasion resistance was not greatly influenced by inclusion of Class C fly ash up to 40% of total cementitious materials. However, a slight decrease in abrasion resistance of high-volume fly ash (HVFA) concrete (especially at fly ash content above 50%) was noted as compared to the reference mixture without fly ash.
Get full access to this article
View all available purchase options and get full access to this article.
References
American Concrete Institute (ACI) Committee 201. (1992). “Guide to durable concrete.” ACI manual of concrete practice, ACI 201.2R-77, Detroit, 201.2R-1 to 201.2R-37.
Barrow, R. S., Hadchiti, K. M., Carrasquillo, P. M., and Carrasquillo, R. L. (1989). “Temperature rise and durability of concrete containing fly ash.” Proc., CANMET/ACI 3rd Int. Conf. on the Use of Fly Ash, Silica Fume, Slag, and Natural Pozzolans in Concrete, V. M. Malhotra, ed., American Concrete Institute, Detroit, 1, 331–348.
Bilodeau, A., and Malhotra, V. M. (1992). “Concrete incorporating high volumes of ASTM Class F fly ashes: mechanical properties and resistance to deicing salt scaling and to chloride-ion penetration.” Proc., CANMET/ACI 4th Int. Conf. on the Use of Fly Ash, Silica Fume, Slag, and Natural Pozzolans in Concrete, V. M. Malhotra, ed., American Concrete Institute, Detroit, 1, 319–349.
Fentress, B.(1973). “Slab construction practice compared by wear tests.” ACI J., 70(7), 486–491.
Gebler, S. H., and Klieger, P. (1986). “Effect of fly ash on physical properties of concrete.” Proc., CANMET/ACI 2nd Int. Conf. on the Use of Fly Ash, Silica Fume, Slag, and Natural Pozzolans in Concrete, V. M. Malhotra, ed., American Concrete Institute, Detroit, 1, 1–50.
Hadchti, K. M., and Carrasquillo, R. L. (1988). “Abrasion resistance and scaling resistance of concrete containing fly ash.” Research Rep. 481–3, Center for Transportation Research, Bureau of Engineering Research, Univ. of Texas at Austin, Austin, Tex.
Hemmings, R. T., and Berry, E. E. (1988). “On the glass in coal fly ashes: recent advances.” Proc., Materials Research Symposium, Material Research Society, Warrendale, Pa.
Kettle, R., and Sadegzadah, M. (1987). “The influence of construction procedures on abrasion resistance.” ACI Special Publication No. SP-100, American Concrete Institute, Detroit, 1385–1410.
Mehta, P. K., and Monteiro, P. J. M. (1993). Concrete structure, properties, and materials, 2nd Ed., Prentice-Hall, Englewood Cliff, N.J.
Naik, T. R., Ramme, B. W., and Tews, J. H.(1995a). “Pavement construction with high volume Class C and Class F fly ash concrete.” ACI Mater. J., 92(2), 200–210.
Naik, T. R., and Singh, S. S. (1991). “Effects of inclusion of fly ash on abrasion resistance of concrete.” Proc., 2nd CANMET/ACI Conf. on Durability of Concrete, American Concrete Institute, Detroit, 683–707.
Naik, T. R., Singh, S. S., and Hossain, M. M. (1993). “Abrasion resistance of high-volume fly ash concrete systems.” Rep. No. 176 Prepared for EPRI, Center for By-products Utilization, Univ. of Wisconsin-Milwaukee, Milwaukee.
Naik, T. R., Singh, S. S., and Hossain, M. M.(1994). “Abrasion resistance of concrete as influenced by inclusion of fly ash.” International Journal of Cement and Concrete Research, 24(2), 301–312.
Naik, T. R., Singh, S. S., and Hossain, M. M.(1995b). “Abrasion resistance of high-strength concrete of concrete made with Class C fly ash.” ACI Mater. J. 92(6), 649–659.
Nanni, A.(1988). “Curing of roller compacted concrete: strength development.” J. Transp. Eng., 114(6), 684–694.
Sadeyzadeh, M., Page, C. L., and Kettle, R. J.(1987). “Surface microstructure and abrasion resistance of concrete.” Cem. Concr. Res., 17(4), 581–590.
Senbetta, E., and Malchow, G. (1987). “Studies on control of durability of concrete through proper curing.” Proc., Katharine and Bryant Mather Int. Conf. on Concrete Durability, American Concrete Institute, Detroit, 1, 73–87.
Tikalsky, P. J., Carrasquillo, P. M., and Carrasquillo, R. L.(1988). “Strength and durability considerations affecting mix proportioning of concrete containing fly ash.” ACI Mater. J., 85(6), 505–511.
Ukita, K., Shigematsu, S., and Ishic, M. (1989). “Improvements in the properties of concrete utilizing classified fly ash.” Proc., CANMET/ACI 3rd Int. Conf. on the Use of Fly Ash, Silica Fume, Slag, and Natural Pozzolans in Concrete, V. M. Malhotra, ed., American Concrete Institute, Detroit, 1, 219–240.
Witte, L. P., and Backstrom, J. E.(1951). “Some properties affecting the abrasion resistance of air-entrained concrete.” ASTM Proceedings, 51, 1141–1155.
Ytterburg, R. F.(1971). “Wear-resistant industrial floors of portland cement concrete.” Civ. Eng. (N.Y.), 41(1), 68–71.
Information & Authors
Information
Published In
Copyright
Copyright © 2002 American Society of Civil Engineers.
History
Received: Apr 3, 1998
Accepted: Nov 7, 2001
Published online: Sep 13, 2002
Published in print: Oct 2002
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.