Testing and Response of Large Diameter Brittle Materials Subjected to High Strain Rate
Publication: Journal of Materials in Civil Engineering
Volume 14, Issue 3
Abstract
Tests on large diameter specimens using a split Hopkinson pressure bar (SHPB) facility are essential to obtain representative dynamic characteristics of engineering materials such as rocks, concrete, and steel fiber-reinforced concrete (SFRC). However, direct application of the conventional SHPB technique to measure the dynamic behavior of these materials has serious limitations, especially if the size of the specimen is relatively large. The background to material testing using the SHPB facility is explored in this paper. The experimental technique and analytical waveform analysis, together with their attendant problems, are presented. Waveform oscillations and nonhomogeneous deformation of brittle specimens are major problems in test data originating from the conventional SHPB technique. These problems are identified and addressed; techniques for circumventing such problems are described. The design and commissioning of a short-length 75 mm diameter SHPB is presented. To overcome a number of problems associated with such a large diameter short length facility, a novel loading method for eliminating oscillation and maintaining uniform deformation of specimens is proposed. Experimental waveforms are presented for brittle engineering materials to underscore the validity of the technique.
Get full access to this article
View all available purchase options and get full access to this article.
References
Bertholf, L. D.(1974). “Feasiblity of two-dimensional numerical analysis of the split-Hopkinson pressure bar system.” J. Appl. Mech., 41, 137–144.
Chree, C.(1889). “The equations of an isotropic elastic solid in polar and cylindrical coordinates, their solutions and applications.” Cambridge Philos. Soc., Trans., 14, 250–369.
Davies, E. D. H., and Hunter, S. C.(1963). “The dynamic compression testing of solids by the method of the split Hopkinson pressure bar.” J. Mech. Phys. Solids, 11, 155–179.
Follansbee, P. S., and Frantz, C.(1983). “Wave propagation in the split Hopkinson pressure bar.” J. Eng. Mater. Technol., 105(1), 61–66.
Gong, J. C., Malvern, D. A., and Jenkins, D. A.(1989). “Dispersion investigation in the split Hopkinson pressure bar.” J. Eng. Mater. Technol., 112, 309–314.
Hakailehto, K. O. (1969). “The behavior of rock under impulse loads—a study using the Hopkinson split bar method.” PhD thesis, Technical Univ., Otaniemi-Helsinki, Acta Polytechnica Scandinanca, Helsinki, Finland.
Kinoshita, S., Sato, K., and Kawakita, M.(1974). “On the mechanical behavior of rocks under impulsive loading.” Bull. Faculty Eng., 83, 51–62.
Kolsky, H.(1949). “An investigation of the mechanical properties of materials at very high strain rates of loading.” Proc. Phys. Soc. London, Sect. B, 62(B), 676–700.
Kumar, A.(1968). “The effect of stress rate and temperature on the strength of basalt and granite.” Geophys. Soc. Exploration Geophysicists, 33(3), 501–510.
Li, X. B., and Gu, D. (1994). Rock impact dynamics, Central-South Univ. of Technology Press, Changsha, P.R. China (in Chinese).
Lifshitz, J. M., and Leber, H.(1994). “Data processing in the split Hopkinson pressure bar tests.” Int. J. Impact Eng., 15(6), 723–733.
Lindholm, U. S., Yeakley, L. M., and Nagy, A.(1974). “The dynamic strength and fracture properties of Dresser basalt.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr., 11(5), 181–192.
Liu, D., and Li, X. B.(1998). “Dynamic inverse design and experimental study of impact pistons.” Chinese J. Mech. Eng., 34(4), 506–514.
Olsson, W. A.(1991). “The compressive strength of tuff as a function of strain rate from to ” Int. J. Rock Mech. Min. Sci. Geomech. Abstr., 28(1), 115–118.
Pochhammer, L.(1876). “On the propagation velocities of small oscillations in an unlimited isotropic circular cylinder.” J. fur die Reine und Angewandte Mathematik, 81, 324–326.
Richard, S.(1957). “Longitudinal impact of a semi-infinite circular elastic bar.” J. Appl. Mech., 24, 59–64.
Ross, C. A., Tedesco, J. W., and Kuennen, S. T.(1995). “Effects of strain rate on concrete strength.” ACI Mater. J., 92(1), 37–47.
Ross, C. A., Thompson, P. Y., and Tedesco, J. W.(1989). “Split-Hopkinson pressure bar tests on concrete and mortar in tension and compression.” ACI Mater. J., 86(5), 475–481.
Zhao, H., and Gary, G.(1996). “On the use of SHPB techniques to determine the dynamic behavior of materials in the range of small strains.” Int. J. Solids Struct., 33(23), 3363–3375.
Zheng, S., Haussler-Combo, U., and Eibl, J.(1999). “New approach to strain rate sensitivity of concrete in compression.” J. Eng. Mech., 125(12), 1403–1410.
Information & Authors
Information
Published In
Copyright
Copyright © 2002 American Society of Civil Engineers.
History
Received: Aug 29, 2000
Accepted: Feb 4, 2001
Published online: May 15, 2002
Published in print: Jun 2002
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.