Flat and Elongated Aggregates in Superpave Regime
Publication: Journal of Materials in Civil Engineering
Volume 12, Issue 2
Abstract
Some states have recommended changing the definition of flat and elongated aggregates from 5:1 to 3:1 and an increase in the maximum allowable percentage of flat and elongated (F&E) particles to 20% or higher in the Superpave aggregate specification. Engineering justification and performance data are required to rationally establish the criteria for this change. The objectives of this research included the statistical analysis of performance indicators of Superpave mixtures containing different levels of 3:1 particles. Three mixes were designed and tested using 0, 15, and 40% of 3:1 particles from a set of Kentucky limestone aggregates. This paper contains the findings, conclusions, and recommendations on the research. The mixtures did not differ significantly in their performance-related properties at lower and higher temperatures. However, at intermediate temperatures, significant differences were observed. A curve shifting analysis confirmed the presence of lower shear stiffness with an increase in the percentage of 3:1 F&E particles. The mix densification trends were inconclusive. Additionally, at low temperatures, the mixes with increasing percentages of 3:1 F&E particles seemed to have higher tensile strengths. This particular finding needs to be further investigated. Overall, increases up to 40% of 3:1 F&E particles did not adversely affect the performance potential of such mixes as measured by the Superpave methodology.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Brown, E. R., Haddock, J. E., Mallick, R. B., and Lynn, T. A. (1997). “Development of mixture design procedure for stone matrix asphalt (SMA).” J. Assn. of Asphalt Paving Technologists, 66.
2.
Cominsky, R. J., Huber, G. A., and Anderson, R. M. (1994). “The superpave mix design manual for new construction and overlays.” SHRP Rep. A-407, National Research Council, Washington, D.C.
3.
Goodrich, J. L. (1991). “Asphaltic binder rheology, asphalt concrete rheology and asphalt concrete mix properties.” J. Assn. of Asphalt Paving Technologists, 60.
4.
Huber, G. A., Jones, J. C., and Jackson, N. M. (1998). “Contribution of fine aggregate angularity and particle shape to superpave mixture performance.” Transp. Res. Rec. 1630, Transportation Research Board, National Research Council, Washington, D.C.
5.
Lees, G. (1964). “The measurement of particle elongation and flakiness: A critical discussion of British standard and other test methods.” Mag. of Concrete Res., 16(49).
6.
Li, M. C., and Kett, I. (1967). “Influence of coarse aggregate shape on the strength of asphalt concrete mixtures.” Hwy. Res. Rec. 178, 93–106.
7.
Livneh, M., and Greenstein, J. (1972). “Influence of aggregate shape on engineering properties of asphaltic paving mixtures.” Hwy. Res. Rec. 404.
8.
Stephens, J. E., and Sinha, K. C. (1978). “Effect of aggregate shape on bituminous mix character.” J. Assn. of Asphalt Paving Technologists, 47, 434–456.
9.
“Superpave asphalt mixture analysis—course text.” (1996a). Asphalt Inst. Res. Ctr., National Asphalt Training Center II, Lexington, Ky.
10.
“Superpave mix design.” (1966b). Superpave Ser. No. 2 (SP-2), Asphalt Inst. Res. Ctr., Asphalt Institute, Lexington, KY.
Information & Authors
Information
Published In
History
Received: May 8, 1999
Published online: May 1, 2000
Published in print: May 2000
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.