Accelerated Corrosion and Embrittlement of High-Strength Bridge Wire
Publication: Journal of Materials in Civil Engineering
Volume 12, Issue 1
Abstract
Suspension bridge cable inspections have revealed severely corroded and broken wires in some main cables. Accelerated, cyclic corrosion studies were conducted to assess the relative effect of general corrosion, corrosion cracking, and hydrogen embrittlement on the deterioration in material properties of high-strength steel bridge wire. Galvanized and ungalvanized wire samples were corroded in a cabinet that cyclically applied an acidic salt spray, dry conditions, and 100% relative humidity at elevated temperatures. Specimens under zero applied load, and under tensile loads of up to 22 kN (5,000 lb) were studied. Mass loss, hydrogen concentration, ultimate load, and elongation at failure were obtained from corroded and uncorroded samples. Elongation measurements indicate a significant embrittlement of the wires, a result supported by fracture surface morphology. Ultimate load was found to degrade at a rate in excess of that attributable to material loss by general corrosion. The hydrogen content of corroded wire was found to be greater than that of uncorroded wire, particularly for galvanized wire.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Balsamo, F. P. ( 1993). “Suspension bridges.” Bridge inspection and rehabilitation: A practical guide, L. G. Silano, ed., Wiley, New York, 117–132.
2.
Bieniek, M. P. (1991). “Suspension bridges: Design for durability.” Proc., Int. Workshop on Technol. for Hong Kong's Infrastructure Devel., J. C. Chen and J. L. Beck, eds., Commercial Press, Hong Kong.
3.
Bieniek, M. P. (1993). “Safety and aging of cables of suspension bridges.” Proc., 4th Int. Conf. on Struct. Failure, Product Liability, and Tech. Insurance, H. P. Rossmanith, ed., Elsevier, New York.
4.
Eiselstein, L. E., and Caligiuri, R. D. ( 1988). “Atmospheric corrosion of the suspension cables on the Williamsburg Bridge.” Degradation of metals in the atmosphere, Spec. Tech. Publ. 965, S. W. Dean and T. S. Lee, eds., ASTM, Philadelphia, 78–95.
5.
Hartt, W. H., Kumria, C. C., and Kessler, R. J. (1993). “Influence of potential, chlorides, pH, and precharging time on embrittlement of cathodically polarized prestressing steel.” Corrosion, 49(5), 377–385.
6.
Haynes, G. S. ( 1995a). “Cabinet testing.” Corrosion tests and standards: Application and interpretation, R. Baboian, ed., ASTM, Philadelphia, 91–97.
7.
Haynes, G. S. ( 1995b). “Overview.” Cyclic cabinet corrosion testing, Spec. Tech. Publ. 1238, G. S. Haynes, ed., ASTM, Philadelphia, vi–viii.
8.
Hertzberg, R. W. (1995). Deformation and fracture mechanics of engineering materials, Wiley, New York.
9.
Huang, H. ( 1993). “Investigation into the mechanism of mechanical degradation of deformed pipeline steel exposed to a sour gas environment,” PhD thesis, Univ. of Calgary, Calgary, Alta., Canada.
10.
Huang, H., and Shaw, W. J. D. (1995). “Hydrogen embrittlement interactions in cold-worked steel.” Corrosion, 51(1), 30–36.
11.
Miyoshi, Y., Kitayama, M., Nishimura, K., and Naito, S. ( 1983). “Cosmetic corrosion mechanism of zinc and zinc alloy coated steel sheet for automobiles.” Tech. Paper No. 850007. SAE, Warrendale, Pa.
12.
Oriani, R. A., Hirth, J. P., and Smialowski, M., eds. (1985). Hydrogen degradation of ferrous alloys, Noyes Publications, Park Ridge, NJ.
13.
Seabrook, J. B., Grant, N. J., and Carney, D. (1950). “Hydrogen embrittlement of SAE 1020 steel.” Trans. AIME J. of Metals, 188, 1317–1321.
14.
Stahl, F. L., and Gagnon, C. P. (1996). Cable corrosion in bridges and other structures: Causes and solutions, ASCE Press, New York.
15.
“Standard practice for modified salt spray (fog) testing.” G 85-94, ASTM, West Conshohocken, Pa.
16.
“Standard practice for preparing, cleaning, and evaluating corrosion test specimens.” G 1-90(1994)e1, ASTM, West Conshohocken, Pa.
17.
“Standard test methods for determination of carbon, sulfur, nitrogen, and oxygen in steel and in iron, nickel, and cobalt alloys.” E 1019-94e1, ASTM, West Conshohocken, Pa.
18.
“Standard test methods for tension testing of metallic materials.” (1996). E 8-96a, ASTM, West Conshohocken, Pa.
19.
Standish, J. V., Whelan, G. W., and Roberts, T. R. (1983). “Corrosion behavior of galvanized and cold rolled steels.” Proc., 2nd Automotive Corrosion Prevention Conf., Tech. Paper No. 831810. SAE, Warrendale, Pa.
20.
Timmins, P. F. (1997). Solutions to hydrogen attack in steels, ASM International, Materials Park, Ohio.
21.
Tins, J. (1996). “High tensile steel wires for bridge cables.” Wire J. Int., 29(7), 82–90.
22.
Troiano, A. R. (1960). “The role of hydrogen and other interstitials in the mechanical behavior of metals.” Trans. ASM, 52, 54–80.
Information & Authors
Information
Published In
History
Received: Jul 6, 1998
Published online: Feb 1, 2000
Published in print: Feb 2000
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.