Optimal Steel Fiber Strength for Reinforcement of Cementitious Materials
Publication: Journal of Materials in Civil Engineering
Volume 11, Issue 2
Abstract
Steel fiber is the most common type of fiber reinforcement in cementitious materials. The reinforcement efficiency, in terms of maximum crack bridging force and total energy absorption during fiber pullout, is a function of many parameters including the properties of fiber, matrix, and interface as well as fiber size, volume fraction, geometry, and distribution. In this investigation, we focus on the effect of fiber yield strength on reinforcement efficiency. Fiber pullout specimens are fabricated with fibers of different yield strengths. Because cracks in a concrete member may intersect fibers at different angles, pullout tests are carried out with the fiber inclined at 0, 30, and 60°. The experimental results indicate the existence of an optimal fiber yield strength for the maximization of pullout load and pullout work. Inspection of the pullout curves as well as microscopic studies show that a higher fiber yield strength will result in more severe matrix spalling around the fiber exit point, thus limiting the further improvement in reinforcement efficiency. The results confirm the qualitative trend predicted by an existing theoretical model and indicate that the fiber yield strength is an important parameter that should not be overlooked in the design of fiber reinforced cementitious composites.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Balaguru, P. N., and Shah, S. P. ( 1992). Fiber reinforced cement composites. McGraw-Hill, New York.
2.
Banthia, N., and Trottier, J. F. ( 1994). “Concrete reinforced with deformed steel fibers, Part I: Bond-slip mechanisms.” ACI Mat. J., 91(5), 435–446.
3.
Banthia, N., Trottier, J.-F., Pigeon, M., and Krishnadev, M. R. ( 1992). “Deformed steel fiber pull-out: Material characteristics and metallurgical processes.” High performance cement composites, H. W. Reinhardt and A. E. Naaman, eds., E & FN Spon, London, 456–466.
4.
Banthia, N., Yan, N., Chan, C., Yan, C., and Bentur, A. ( 1995). “Bond-slip mechanisms in steel micro-fiber reinforced cement composites.” Proc., Microstruct. of cement based systems/bonding and interfaces in cementitious mat., Vol. 370, S. Diamond, S. Mindess, F. P. Glasser, L. R. Roberts, J. P. Skalny, and L. D. Wakely, eds., 538–549.
5.
Bentur, A., and Mindess, S. ( 1990). Fiber reinforced cementitious composites. Elsevier Science, Essex, England, U.K.
6.
Gao, Y., Mai, Y. W., and Cotterell, B. ( 1988). “Fracture of fiber-reinforced materials.” J. Appl. Math. and Phys. (ZAMP), 39, 550–572.
7.
Geng, Y., and Leung, C. K. Y. ( 1996). “A microstructural study of the fiber/mortar interface during fiber debonding/pullout.” J. Mat. Sci., 31, 1285–1294.
8.
Gopalaratnam, V. S., and Shah, S. P. (1987). “Tensile fracture of steel fiber reinforced concrete.”J. Engrg. Mech., ASCE, 113(5), 635–653.
9.
Katz, A., and Li, V. C. (1995). “Inclination angle effect of carbon fibers in cementitious composites.”J. Engrg. Mech., ASCE, 121(12), 1340–1348.
10.
Krishnadev, M. R., Berrada, S., Banthia, N., and Fortier, J.-F. ( 1992). “Deformed steel fiber pull-out mechanics: Influence of steel properties.” Fibre reinforced cement and concrete, R. N. Swamy, ed., E & FN Spon, London, 390–399.
11.
Lawrence, P. ( 1972). “Some theoretical considerations of fiber pull-out from an elastic matrix.” J. Mat. Sci., 7(1), 1–6.
12.
Leung, C. K. Y. (1992). “Fracture-based two-way debonding model for discontinuous fibers in elastic matrix.”J. Engrg. Mech., ASCE, 118(11), 2298–2318.
13.
Leung, C. K. Y. (1996). “Design criteria for pseudoductile fiber-reinforced composites.”J. Engrg. Mech., ASCE, 122(1), 10–18.
14.
Leung, C. K. Y., and Chi, J. (1995). “Crack bridging force in random ductile fiber brittle matrix composites.”J. Engrg. Mech., ASCE, 121(12), 1315–1324.
15.
Leung, C. K. Y., and Li, V. C. ( 1992). “Effect of fiber inclination on crack bridging stress in brittle fiber reinforced brittle matrix composites.” J. Mech. Phys. Solids, 40(6), 1333–1362.
16.
Li, V. C., and Leung, C. K. Y. (1992). “Tensile failure modes of random discontinuous fiber reinforced brittle matrix composites.”J. Engrg. Mech., ASCE, 118(11), 2246–2264.
17.
Li, V. C., Wang, Y., and Backer, S. ( 1990). “Effect of inclining angle, bundling, and surface treatment on synthetic fiber pull-out from a cement matrix.” Comp., 21(2), 132–140.
18.
Li, V. C., and Wu, H. C. ( 1992). “Micromechanics based design for pseudo strain-hardening in cementitious composites.” Proc., 9th ASCE Conf. on Engrg. Mech., L. D. Lutes and J. M. Niedzwecki, eds., ASCE, Reston, Va., 740–743.
19.
Li, Z., Mobasher, B., and Shah, S. P. ( 1991). “Characterization of interfacial properties in fiber reinforced cementitious composites.” J. Am. Ceramic Soc., 74(9), 2156–2164.
20.
Morton, J., and Groves, G. W. ( 1974). “The cracking of composites consisting of discontinuous ductile fibers in a brittle matrix—Effect of fiber orientation.” J. Mat. Sci., 9, 1436–1445.
21.
Naaman, A. E., and Shah, S. P. (1976). “Pull-out mechanism in steel fiber-reinforced concrete.”J. Struct. Div., ASCE, 102(8), 1537–1548.
22.
Ouyang, C., Pacios, A., and Shah, S. P. (1994). “Pullout of inclined fibers from cementitious matrix.”J. Engrg. Mech., ASCE, 120(12), 2641–2659.
Information & Authors
Information
Published In
Journal of Materials in Civil Engineering
Volume 11 • Issue 2 • May 1999
Pages: 116 - 123
History
Published online: May 1, 1999
Published in print: May 1999
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.