Support Structures for High‐Resolution Optical Systems
Publication: Journal of Aerospace Engineering
Volume 5, Issue 1
Abstract
High‐resolution optical systems require support structures that isolate the optical elements from mechanical and thermal loadings. Because the requirements for precise fabrication of the support structure are generally much less rigorous than they are for the optical element surface, the optical quality of the system can be degraded if the optical element is rigidly attached to the support structure. For small optics that can be treated as rigid elements, kinematic (statically determinate, point support) mountings may be used. For larger optics, however, finite contact surfaces (pads) are required to reduce contact stresses so that a semikinematic support results. If the contact surfaces are not coplanar, the optical element can be distorted. To circumvent this latter problem, support pads with self‐aligning designs may be used. These designs may either be mechanisms or flexures. Flexures are used more generally because they are free of both friction and hysteresis. For large optics, the optical elements require numerous supports so that the support system is highly statically indeterminant. These systems require analysis using the finite element method to meet optical deflection design criteria.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Chin, D. (1964). Applied optics, 3, 895–906.
2.
Espiard, J. (1985). “Lightweight cold mirror and fixation,” The International Society for Optical Engineering, 589, 38–46.
3.
Hog, E. (1975). Astronomy and astrophysics, 41, 107.
4.
Jones, R. V. (1956). “Flexure designs.” J. Sci. Instr., 33(11), 12–18.
5.
Levina, Z. M. (1968). “Research on the static stiffness of joints in machine tools.” Advances in machine tool design and research, S. A. Tobias and F. Koenigsberger, eds., Pergamon Press, London, England.
6.
Marschall, C. W., and Maringer, R. E. (1977). Dimensional instability. Pergamon Press, Elmsford, N.Y.
7.
Nelson, J. E., and Mast, T. (1984). “The Keck telescope primary mirror.” LIC TMC Science Office Reports Series, Lawrence Livermore Laboratory, Livermore, Calif.
8.
Neugebauer, G. H. (1980). “Designing springs for parallel motion.” Machine design, 119–120.
9.
Pepi, J. W., Kahan, M., Barnes, W. H., and Zielinski, R. J. (1980). “Teal Ruby‐Design manufacture and test.” The International Society for Optical Engineering, 216, 160–173.
10.
Richard, R. M., Vukobratovich, D., Pollard, L. M., Cho, M., and Melugin, R. K. (1988). “A flexure assembly for the SIRTF one‐meter primary mirror,” The International Society for Optical Engineering, 973, 79–99.
11.
Richard, R. M., and Williams, G. C. (1985). “Optical performance analysis of 4‐, altazimuth‐mounted primary telescope mirrors.” Design Report, The National Optical Astronomy Observatories, Tucson, Ariz.
12.
Schlegelmilch, R., and Altman, J. (1985). “A cooled infrared telescope for the GIRL German infrared laboratory.” Neiss Information, 28, 19.
13.
Schreibman, M., and Young, P. (1980). “Design of infrared astronomical satellite (IRAS) primary mirror mounts.” The International Society for Optical Engineering, 250, 134–146.
14.
Sidall, G. J. (1970). “The design and performance of flexure pivots for instruments,” thesis presented to the Univ. of Aberdeen at Aberdeen, U.K., in partial fulfillment of the requirements for the degree of Master of Science.
15.
Trylinski, W. (1971). Fine mechanisms and precision instruments. Pergamon Press, Warsaw, Poland.
16.
Vukobratovich, D. (1980). “Large five‐axis mounts.” Workshop on Optical Fabrication and Testing, Optical Society of America, North Falmouth, Mass., 146–151.
17.
Yoder, P. R., Jr. (1986). Opto‐mechanical systems design. Marcel‐Dekker, New York, N.Y.
Information & Authors
Information
Published In
Journal of Aerospace Engineering
Volume 5 • Issue 1 • January 1992
Pages: 24 - 43
Copyright
Copyright © 1992 ASCE.
History
Published online: Jan 1, 1992
Published in print: Jan 1992
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.