Collapse Study of an Unreinforced Masonry Bearing Wall Building Subjected to Internal Blast Loading
Publication: Journal of Performance of Constructed Facilities
Volume 22, Issue 2
Abstract
A blast test was conducted inside a conventional, two-story, unreinforced, brick, bearing wall building scheduled to be demolished. A credible explosive device was placed inside the building on the ground floor and was detonated to investigate whether or not the building would collapse. The measured blast pressures, key material properties of the structure, and the structural configuration were used as input parameters to a single-degree-of-freedom software program, the single-degree-of-freedom blast effects design spreadsheet (SBEDS), commonly used in the United States to model unreinforced masonry walls subjected to blast loading. The net effect of overburden loads on the ground-floor bearing walls, including uplift by blast pressures on the ground-floor ceiling, was considered when investigating the validity of an appropriate resistance function (available in SBEDS) that defines out-of-plane bearing wall response. Comparisons were made between analytical and experimental permanent wall deflections and two alternatives, a simple displacement-based criterion and a resistance criterion, were used to estimate the building’s state relative to its estimated collapse limit state. It was found that SBEDS was able to model the experimental deflections quite well if effective input parameters were carefully considered. As a result, analytical and experimental determinations of the structure’s state were also in good agreement.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Partial funding for this research was provided by the National Science Foundation under Grant No. CMS-0342103.
References
Baylot, J. T., Bullock, B., Slawson, T. R., and Woodsen, S. C. (2005). “Blast response of lightly attached concrete masonry unit walls.” J. Struct. Eng., 131(8), 1186–1193.
Biggs, J. M. (1964). Introduction to structural dynamics, McGraw-Hill, New York.
Davidson, J. S., Fisher, J., Hammons, M., Porter, J., and Dinan, R. (2005). “Failure mechanisms of polymer-reinforced concrete masonry walls subjected to blast.” J. Struct. Eng., 131(8), 1194–1205.
Davidson, J. S., Porter, J. R., Dinan, R. J., Hammons, M. I., and Connell, J. D. (2004). “Explosive testing of polymer retrofit masonry walls.” J. Perform. Constr. Facil., 18(2), 100–106.
Dennis, S. T., Baylot, J. T., and Woodson, S. C. (2002). “Response of one-fourth-scale concrete masonry unit (CMU) walls to blast.” J. Eng. Mech., 128(2), 134–142.
Doherty, K., Griffith, M. C., Lam, N., and Wilson, J. (2002). “Displacement-based seismic analysis for out-of-plane bending of unreinforced masonry walls.” Earthquake Eng. Struct. Dyn., 31(4), 833–850.
Flanagan, R. D., and Bennett, R. M. (1999). “Arching of masonry infilled frames: Comparison of analytical methods.” Pract. Period. Struct. Des. Constr., 4(3), 105–110.
Griffith, M. C., Lam, N. T. K., Wilson, J. L., and Doherty, K. (2004). “Experimental investigation of unreinforced brick masonry walls in flexure.” J. Struct. Eng., 130(3), 423–432.
Henderson, R. C., Fricke, K. E., Jones, W. D., Beavers, J. E., and Bennett, R. M. (2003). “Summary of large- and small-scale unreinforced masonry infill test program.” J. Struct. Eng., 129(12), 1667–1675.
Hinman, E., and Hammond, D. J. (1997). Lessons from the Oklahoma City bombing: Defensive design techniques, ASCE, Roston, Va.
La Mendola, L., Papia, M., and Zingone, G. (1995). “Stability of masonry walls subjected to seismic transverse forces.” J. Struct. Eng., 121(11), 1581–1587.
Lu, M., Shultz, A. E., and Stolarski, H. K. (2004). “Analysis of the influence of tensile strength on the stability of eccentrically compressed slender unreinforced masonry walls under lateral loads.” J. Struct. Eng., 130(6), 921–933.
Mays, G. C., Hetherington, J. G., and Rose, T. A. (1998). “Resistance–deflection functions for concrete wall panels with openings.” J. Struct. Eng., 124(5), 579–587.
McDowell, E. L., McKee, K. E., and Sevin, E. (1956). “Arching action theory of masonry walls.” J. Struct. Div., 82(2), 1–18.
Oswald, C. J. (2005). “Component explosive damage assessment workbook.” Contract No. DACA45-01-D-007-0013, prepared by Baker Engineering and Risk Consultants for the U.S. Army Corps of Engineers Protective Design Center.
Sunshine, D., Amini, A., and Swanson, M. (2004). “Overview of Simplified Methods and Research for Blast Analysis.” Proc., Structures 2004—Building on the Past: Securing the Future, ASCE, Reston, Va., 1–11.
Tesfaye, E., and Broome, T. H. (1977). “Effect of weight on stability of masonry walls.” J. Struct. Div., 103(5), 961–970.
U.S. Army Corps of Engineers (USACE). (2002). “Design and analysis of hardened structures for conventional weapons effects.” UFC 3-340-01, USACE, Washington, D.C.
U.S. Army Corps of Engineers (USACE). (2006). “SBEDS user guide.” PDC TR 06-01, USACE, Washington, D.C.
U.S. Army Engineer Research and Development Center (USERDC). (2003). ConWep, version 2.0.5.0, USERCD, Washington, D.C.
U.S. Army, U.S. Navy, and U.S. Air Force (Army/Navy/Air Force). (1999). “Structures to resist the effects of accidental explosions.” Army TM5-1300, Navy NAVFAC P397, Air Force Regulation No. 88-22, Dept. of Defense Explosives Safety Board, Alexandria, Va.
Information & Authors
Information
Published In
Copyright
© 2008 ASCE.
History
Received: Jan 2, 2007
Accepted: Jun 19, 2007
Published online: Apr 1, 2008
Published in print: Apr 2008
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.