Integral Abutment Bridges: Current Practice in United States and Canada
Publication: Journal of Performance of Constructed Facilities
Volume 14, Issue 3
Abstract
Integral abutment bridges have been gaining popularity among bridge owners as cost-effective alternatives to bridges with conventional joints. They reduce initial construction costs and long-term maintenance expenses, improve seismic resistance, and extend long-term serviceability. New York has been building them since the late 1970s, with a wide variety of details, and they have been performing well. For further improvement of New York's design practice, a comparative survey was undertaken across North America, focusing on design and construction of both substructures and superstructures. In all, 39 states and Canadian provinces responded, including 8 who said they had no experience with these bridges. Responses are analyzed and summarized in this paper. Overall, integral abutment bridges are performing as well as, if not better than, conventional bridges, but no uniform national standards exist for their design. Design practices and assumptions concerning limits of thermal movement, soil pressure, and pile design vary considerably among responding agencies. These decisions are based largely on past experience. Validity of these assumptions needs investigation by testing and analysis to ensure efficient and reliable design.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
AASHTO. (1996). Standard specifications for highway bridges, 16th ed., Washington, D.C.
2.
Abendroth, R. E., and Greimann, L. F. (1989). “A rational design approach for integral abutment bridges.” Transp. Res. Rec. 1223, Transportation Research Board, Washington, D.C., 12–23.
3.
Abendroth, R. E., and Greimann, L. F. (1990). “Pile behavior established from model test.”J. Geotech. Engrg., ASCE, 116(4), 571–588.
4.
Abendroth, R. E., Greimann, L. F., and Ebner, P. B. (1989). “Abutment pile design for jointless bridges.”J. Struct. Div., ASCE, 115(11), 2914–2929.
5.
Alampalli, S. A., and Lall, J. ( 1996). “Distribution of pile loads and earth pressures for design of integral-abutment bridges.” Study proposal for res. proj. 226-1, New York State Department of Transportation, Albany, N.Y.
6.
Alampalli, S., and Yannotti, A. P. (1998). “In-service performance of integral bridges and jointless decks.” Transp. Res. Rec. 1624, Transportation Research Board, Washington, D.C., 1–7.
7.
Boardman, W. G. (1997). North American bridge deck joint elimination survey results summary. Rhode Island Department of Transportation, Providence, R.I.
8.
Broms, B. B., and Ingelson, I. (1972). “Lateral earth pressure on a bridge abutment.” Proc., 5th Eur. Conf. on Soil Mech. and Found. Engrg., Sociedad Espanola de Mechanica de Suelo y Cimentaciones, Madrid, Vol. 1.
9.
“Bridge detail (BD) sheets IA1 through IA3, integral abutments.” (1996). Engrg. Instruction 96-035, Struct. Des. and Constr. Div., New York State Department of Transportation, Albany, N.Y.
10.
Burke Jr., M. P. (1990). “Integral bridge design is on the rise.” Modern Steel Constr., 30(4), 9–11.
11.
Burke Jr., M. P. (1997). “The structure movement systems approach to effective bridge design.” Transp. Res. Rec. 1594, Transportation Research Board, Washington, D.C., 147–153.
12.
Girton, D., Hawkinson, T., and Greimann, L. (1991). “Validation of design recommendation for integral abutment piles.”J. Struct. Engrg., ASCE, 117(7), 2117–2134.
13.
Greimann, L., Hawkinson, T., Abendroth, R., and Girton, D. (1992). “Design recommendations for integral abutment piles.” Proc., ESE/CSCE Int. Colloquium on Struct. Engrg., Cairo, Egypt.
14.
Hoppe, E. J., and Gomez, J. P. (1996). “Field study of an integral backwall bridge.” Final Rep. VTRC 97-R7, Virginia Transportation Research Council, Charlottesville, Va.
15.
Integral bridge abutments: Report on condition and performance. (1995). Struct. Des. Constr. Div., New York State Department of Transportation, Albany, N.Y.
16.
Thippeswamy, H. K., and GangaRao, H. V. S. (1995). “Analysis of in-service jointless bridges.” Transp. Res. Rec. 1476, Transportation Research Board, Washington, D.C., 162–170.
17.
Thippeswamy, H. K., Raju, P. R., and GangaRao, H. V. S. (1994). “Parametric study of single-span jointless steel bridges.” Transp. Res. Rec. 1460, Transportation Research Board, Washington, D.C., 25–36.
18.
Wolde-Tinsae, A. M., and Klinger, J. E. (1987). “Integral bridge design and construction.” Rep. FHWA/MD-87/04, Maryland Department of Transportation, Baltimore-Washington International Airport, Md.
Information & Authors
Information
Published In
History
Received: Sep 27, 1999
Published online: Aug 1, 2000
Published in print: Aug 2000
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.