Reliability Based Earthquake Design Guidelines for Marine Structures
Publication: Journal of Waterway, Port, Coastal, and Ocean Engineering
Volume 125, Issue 5
Abstract
This paper describes a reliability based formulation to determine earthquake LRFD parameters for conventional, steel, pile supported, tubular member platforms that is proposed as a basis for earthquake design criteria and guidelines for offshore platforms and that is intended to have worldwide applicability. The formulation is illustrated with application to platforms located in five areas: offshore California, Venezuela (Rio Caribe), the East Coast of Canada, the Caspian Sea (Azeri), and the Norwegian sector of the North Sea. The approach and proposed quantifications have been verified with site specific results from four locations. Good agreements have been developed between the site specific results and those based on these guidelines. The approach provides an important element of information sensitivity that allows the loading and resistance factors to be varied as a function of the desired reliability for a platform, the unique aspects of its seismic environment, and the primary uncertainties in the earthquake loadings and platform element capacities.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Bazzurro, P., and Cornell, C. A. (1994a). “Seismic hazard analysis of nonlinear structures. I: Methodology.”J. Struct. Engrg., ASCE, 120(11), 3320–3344.
2.
Bazzurro, P., and Cornell, C. A. (1994b). “Seismic hazard analysis of nonlinear structures. II: Applications.”J. Struct. Engrg., ASCE, 120(11), 3345–3365.
3.
Bea, R. G. (1977). “Oceanographic and earthquake criteria, the Gulf of Alaska criteria and platform study.” Rep. to American Petroleum Institute, Dallas.
4.
Bea, R. G. (1979). “Earthquake and wave design criteria for offshore platforms.”J. Struct. Div., ASCE, 105(2), 401–419.
5.
Bea, R. G. ( 1990a). Reliability based design criteria for coastal and ocean structures. National Committee on Coastal and Ocean Engineering, Institution of Engineers, Australia, Barton, ACT.
6.
Bea, R. G. (1990b). “Reliability criteria for new and existing platforms.” Proc., Offshore Technol. Conf., OTC 6312, Society of Petroleum Engineers, Richardson, Tex., 393–408.
7.
Bea, R. G. (1991a). “Loading and load effects uncertainties.” Rep. to Can. Standards Assn., Verification Program for CSA Code for the Design, Construction and Installation of Fixed Offshore Structures Project No. D-3, Ont., Canada.
8.
Bea, R. G. (1991b). “Offshore platform reliability acceptance criteria.” J. Drilling Engrg., 25(3), 131–137.
9.
Bea, R. G. (1992). “Seismic design and requalification methodologies for offshore platforms.” Proc., Int. Workshop on Seismic Des. and Requalification of Offshore Struct., California Institute of Technology, Pasadena, Calif., 44–67.
10.
Bea, R. G. (1993). “Reliability based requalification criteria for offshore platforms.” Proc., 12th Int. Conf. on Offshore Mech. and Arctic Engrg., OMAE'93, Safety and Reliability Symp., American Society of Mechanical Engineers. New York, 133–147.
11.
Bea, R. G. (1996). “Probability based earthquake load & resistance factor design criteria for offshore platforms.” Proc., Offshore Technol. Conf., OTC 8106, Society of Petroleum Engineers, Richardson, Tex., 763–799.
12.
Bea, R. G., Audibert, J. M. E., and Akky, M. R. (1979). “Earthquake response of offshore platforms.”J. Struct. Div., ASCE, 105(2), 377–400.
13.
Bea, R. G., Landeis, B., and Craig, M. J. K. (1992). “Re-qualification of a platform in Cook Inlet, Alaska.” Proc., Offshore Technol. Conf., OTC 6935, Society of Petroleum Engineers, Richardson, Tex., 551–563.
14.
Bea, R. G., Mosaddad, B., Vaish, A. K., and Ortiz, K. (1987). “Seismic load effects study.” Rep. to the Am. Petroleum Inst., Dallas.
15.
Bea, R. G., and Young, C. N. (1993). “Loading and capacity effects on platform performance in extreme storm waves and earthquakes.” Proc., Offshore Technol Conf., OTC 7140, Society of Petroleum Engineers, Richardson, Tex.
16.
Borcherdt, R. D. (1994). “Estimates of site-dependent response spectra for design (methodology and justification).” Earthquake Spectra, 10(4), 20–31.
17.
Bungum, H., and Selnes, P. B. ( 1988). Earthquake loading on the Norwegian Continental Shelf. ELOCS, Norwegian Geotechnical Institute, Norsar, Principia, Oslo.
18.
Chang, B. ( 1995). “API/ISO/WG3/Panel 5—seismic loads & response earthquake response spectrum data.” Document Released to ISO Panel 5 for Devel. of Earthquake Des. Guidelines, Houston.
19.
Cornell, C. A. (1994). “Risk-based structural design.” Proc., Symp. on Risk Anal., University of Michigan, Ann Arbor, Mich., 1–15.
20.
Craig, M. J. K. ( 1994). “ISO WG3/Panel 5—9/28/94 meeting minutes.” Document ISO/TC67/SC7/WG3/P5 (Craig9), October 9.
21.
Crouse, C. B., and McGuire, J. W. (1994). “Site response studies for purpose of revising NEHRP seismic provisions. Proc., SMIP 94 Seminar on Seismological and Engrg. Implications of Recent Strong-Motion Data, California Division of Mines and Geology, Sacramento, Calif., 35–45.
22.
Dolan, D. K., Crouse, C. B., and Quilter, J. M. (1992). “Seismic reassessment of Maui A.” Proc., Offshore Technol. Conf., OTC 6934, Society of Petroleum Engineers, Richardson, Tex., 344–364.
23.
“Earthquake loads.” (1992). Guidelines concerning loads and load effects, Chapter 4.6, Norwegian Petroleum Directorate, Stavanger, Norway.
24.
Ekngesvik, K., Olufsen, A., and Karunakaran, D. (1987). “Literature survey on parameter uncertainties related to structural analysis of marine structures.” SINTEF Rep. N-7034, Trondheim-NTH, Norway.
25.
Foo, S. H.-C., and Crouse, C. B. (1990). “Evaluation of seismicity and earthquake loading at Hibernia.” Proc., 3rd Can. Conf. on Marine Geotech. Engrg., St. John's, Nfld, Canada, 60–73.
26.
“General requirements, design criteria, the environment, and loads.” (1992). CAN/CSA-S471-92, Canadian Standards Association, Ont., Canada.
27.
Gudmestad, O. T. ( 1995). Correspondence on ISO TC67/SC7/WG3/Panel 5, uncertainties in earthquake intensities and occurrence. Statoil, Stavanger, Norway.
28.
Hellan, ∅., Tandberg, T., and Hellevigt, N. C. (1992). “Nonlinear re-assessment of jacket structures under extreme storm cyclic loading.” Proc., Offshore Mech. and Arctic Engrg. Conf., OMAE'93, American Society of Mechanical Engineers, New York, 55–66.
29.
Marshall, P. W., and Chang, B. (1996). “Structural design considerations.” Proc., Offshore Technol. Conf., OTC 8107, Society of Petroleum Engineers, Richardson, Tex., 781–793.
30.
Martin, G. R., and Dobry, R. ( 1994). “Earthquake site response and seismic code provisions.” Nat. Ctr. for Earthquake Engrg. Res. (NCEER) Bull., 8(4), 1–5.
31.
Miranda, E., and Bertero, V. V. (1994). “Evaluation of strength reduction factors for earthquake-resistant design.” Earthquake Spectra, 10(2), 110–140.
32.
Moses, F. (1986). “Development of preliminary load and resistance design document for fixed offshore platforms.” Final Rep. to the Am. Petroleum Inst., Dallas.
33.
Pagá, M., Sully, J. P., Gajardo, E., and Bea, R. G. (1994). “Site specific platform design: Modification to API code to consider local seismic conditions.” Proc., 5th U.S. Nat. Conf. on Earthquake Engrg., Earthquake Engineering Research Center, Berkeley, Calif., 20–35.
34.
Recommended practice for planning, designing and constructing fixed offshore platforms—API recommended practice 2A (RP 2A)—LRFD. (1993). 20th Ed., American Petroleum Institute, Washington, D.C.
35.
Recommended practice for planning, designing, and constructing fixed offshore platforms—working stress design, supplement 1. (1997). American Petroleum Institute, Washington, D.C.
36.
Smith, C. E. ( 1994). “Dynamic response to offshore steel-jacket platforms subject to measured seafloor seismic ground motions,” PhD dissertation, Dept. of Civ. Engrg., George Washington University, Washington, D.C.
37.
Tang, W. H. (1988). “Offshore axial pile design reliability.” Rep. to the Am. Petroleum Inst., Dallas.
38.
Tang, W. H. (1990). “Offshore lateral pile design reliability.” Rep. to the Am. Petroleum Inst., Dallas.
39.
van de Graaf, J. W., Tromans, P. S., and Efthymiou, M. (1994). “The reliability of offshore structures and its dependence on design code and environment.” Proc., Offshore Technol. Conf., OTC 7382, Society of Petroleum Engineers, Richardson, Tex.
40.
Woo, G., Bungum, H., Nadim, F., Dahle, A., and Alsaker, A. (1988). “Methods and models for computation of earthquake loads on the Norwegian Continental Shelf.” Proj. Rep. on Earthquake Loading on the Norwegian Continental Shelf—ELOCS to Statoil, Norsk Hydro a.s., Esson Norge a.s., A/S Norske Shell, and NTF, Norwegian Geotech. Inst. Proj. 51514, Oslo.
Information & Authors
Information
Published In
History
Received: Nov 18, 1996
Published online: Sep 1, 1999
Published in print: Sep 1999
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.