Difference between In Situ Flexible Pavement Measured and Calculated Stresses and Strains
Publication: Journal of Transportation Engineering
Volume 132, Issue 7
Abstract
One of the 12 instrumented sections of the Virginia Smart Road was used to compare measured vertical compressive stress and measured transverse horizontal strain under the hot-mix asphalt (HMA) layer induced by a 25.8 kN (5.8 kip) single tire and a 39.5 kN (8.9 kip) set of dual tires to those calculated using layered linear elastic theory. The pavement section is composed of 38 mm (1.5 in.) HMA wearing surface, 150 mm (6 in.) of HMA base mix, 75 mm (3 in.) of asphalt stabilized open graded drainage layer, 150 mm (6 in.) of cement stabilized aggregate layer, and 175 mm (7 in.) of unbound aggregate base. The subgrade is a fill material composed mainly of rocks. Measured stresses were obtained using pressure cells embedded in the pavement during construction. Horizontal transverse strain was measured using H-type strain gauges that were also embedded during construction. Temperature in the pavement layers was measured using embedded T-type thermocouples. Theoretically calculated stresses and strains were obtained using software based on the layered-elastic theory (Kenpave, Bisar 3.0, Elsym5, and Everstress 5.0). In addition, two finite-element approaches were used. Results indicated that the layered elastic theory overestimates pavement responses at low and intermediate temperatures, but significantly underestimates the pavement responses to vehicular loading at high temperatures.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research is sponsored by the Virginia Transportation Research Council and the Virginia Department of Transportation. The help of Samer Lahouar of Virginia Tech and the help of David Clark, Kenneth Taylor, and Randy Orren of the Virginia Department of Transportation are greatly appreciated.
References
Al-Qadi, I. L., Elseifi, M. A., and Leonard, D. (2003). “Development of an overlay design model for reflective cracking with and without steel reinforcement.” J. Assoc. Asphalt Pavement Technol., 72, 388–423.
Al-Qadi, I. L., Loulizi, A., Elseifi, M., and Lahouar, S. (2004). “The Virginia Smart Road: The impact of pavement instrumentation on understanding pavement performance.” J. Assoc. Asphalt Pavement Technol., 83, 427–466.
ASTM. (1998). “Standard test method for indirect tension test for resilient modulus of bituminous mixtures.” ASTM D 4123, Vol. 4.03, ASTM, Philadelphia.
Appea, K. A. (2003). “Validation of FWD testing results at the Virginia Smart Road: Theoretically and by instrument responses.” Ph.D. dissertation, Virginia Polytechnic and State Univ., Blacksburg, Va.
Baker, H. B., Buth, M. R., and Van Deusen, D. A. (1994). “Minnesota road research project: Load response, instrumentation, installation, and testing procedures.” Final Rep. MN/PR-94/01, Minnesota Dept. of Transportation, Minneapolis.
Burmister, D. M. (1943). “The theory of stresses and displacements in layered systems and applications to the design of airport runways.” Highw. Res. Board, Proc. Annu. Meet., Vol. 23, 126–144.
Burmister, D. M. (1945). “The general theory of stresses and displacements in layered soil systems.” J. Appl. Phys., 16, 84–94.
Desai, C. S. (1979). Elementary finite-element method, Prentice-Hall, Englewood Cliffs, N.J.
Elseifi, M. (2003). “Performance quantification of interlayer systems in flexible pavements using finite-element analysis, instrument response, and nondestructive testing.” Ph.D. dissertation, Virginia Polytechnic and State Univ., Blacksburg, Va.
Huang, H. Y. (1993). Pavement analysis and design, Prentice-Hall, Upper Saddle River, N.J.
Kopperman, S., Tiller, G., and Tseng, M. (1986). “ELSYM5: Interactive microcomputer version: User’s manual.” Rep. FHWA-TS-87-206, Federal Highway Administration, Washington, D.C.
Loulizi, A., Al-Qadi, I. L., Flintsch, G. W., and Freeman, T. E. (2002a). “Using field measured stresses and strains to quantify flexible pavement responses to loading.” Proc., 9th Int. Conf. on Asphalt Pavements, Copenhagen, Denmark, 179–227.
Loulizi, A., Al-Qadi, I. L., Lahouar, S., and Freeman, T. E. (2002b). “Measurement of vertical compressive stress pulse in flexible pavements and its representation for dynamic loading tests.” Transportation Research Record. 1816, Transportation Research Board, Washington, D.C., 125–136.
Sargand, S. (1994). “Development of an instrumentation plan for the Ohio SPS test pavement.” Final Rep. No. FHWA/OH-94/019, Ohio Dept. of Transportation, Columbus, Ohio.
Tabatabaee, N., Al-Qadi, I. L., and Sebaaly, P. E. (1992). “Field evaluation of pavement instrumentation methods.” J. Test. Eval., 20(2), 144–151.
Uddin, W., Zhang, D., and Fernandez, F. (1994). “Finite-element simulation of pavement discontinuities and dynamic load response.” Transportation Research Record. 1448, Transportation Research Board, Washington, D.C., 100–106.
Virginia Department of Transportation (VDOT). (2002). Road and bridge specification, VDOT, Richmond, Va.
WesTrack Team (1996). “Accelerated field test of performance-related specifications for hot-mix asphalt construction.” Interim Rep. for Contract No. DTFH61-94-C-00004.
Zaghloul, S., and White, T. (1993). “Use of a three-dimensional dynamic finite-element program for analysis of flexible pavement.” Transportation Research Record. 1338, Transportation Research Board, Washington, D.C., 60–69.
Information & Authors
Information
Published In
Copyright
© 2006 ASCE.
History
Received: Jun 16, 2005
Accepted: Dec 20, 2005
Published online: Jul 1, 2006
Published in print: Jul 2006
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.