Unified Design Method for Most No-Dig Rehabilitation Liners
Publication: Journal of Transportation Engineering
Volume 131, Issue 9
Abstract
The liner materials used for pipe renovation are usually designed to meet some minimum consensus standards. Often, the design guidance is listed in the Appendix of the standards. For additional guidance, numerous design manuals, not part of the pipe standards, are distributed by each vendor or technology holder uniquely geared to their own technology. There is clearly a lack of standardized design methods that allow direct comparisons between available materials or provide final designs on an equal performance basis. This paper will provide a unified design approach so that most no-dig pipe rehab liners are designed by the same set of engineering guidance. Engineering issues, pertaining to various loadings imposed on the liner, buckling behavior of the liner allowing for ovality, size of the annulus, wrinkles, annulus grouting, stresses, and strains in the reliner pipe wall, are addressed. This paper would be of interest to technology holders, owners of pipeline networks, pipeline asset managers, consulting engineers, and regulators.
Get full access to this article
View all available purchase options and get full access to this article.
References
American Water Works Association (AWWA). (1996). “Fiberglass pipe design.” Manual M45, 1st Ed., American Water Works Association, Denver, Colo.
Amstutz, E. (1970). “Buckling of pressure shafts and tunnel linings.” Water Power, based on the original work in German in 1950.
Boot, J. C., and Welch, A. J. (1996). “Creep buckling of thin-walled polymeric pipe linings subject to external groundwater pressure.” Thin-Walled Struct., 21, 191–210.
Bucciarelli, L. L., Jr., and Pian, T. H. H. (1967). “Effect of initial imperfection on the instability of a ring confined in an imperfect rigid boundary.” J. Appl. Mech., 34, 979–984.
El-Sawy, K. (1996). “Nonlinear analysis of liners for rigid pipe rehabilitation.” PhD thesis, Univ. of Western Ontario.
Glock, D. (1997). English Translation is “Behavior of liners for rigid pipeline under external water pressure and thermal expansion.” Stahlbau, 7, 212–217.
Jacobsen, S. (1974). “Buckling of circular rings and cylindrical tubes under external pressure.” Water Power.
Jeyapalan, J. K., and Ben Hamida, H. (1988). “Comparison of German to Marston design methods for clay pipes.” J. Transp. Eng., 114(4), 420–434.
Jeyapalan, J. K., and Watkins, R. K. (2004). “Modulus of soil reaction- values for pipeline design.” J. Transp. Eng., 130(1) 43–48.
Kyriakides, S., and Youn, S.-K. (1984). “On the collapse of circular confined rings under external pressure.” Int. J. Solids Struct., 20(7), 699–713.
Levy, M. (1884). “Me’memoire sur un nouveau cas inte’grable du proble’m de l’elastique et l’une de ses applications [Memoir on a new integrable case of the problem of elasticity and one of its applications].” J. Math. Pures Appl., 10, 5–42.
Li, J. Y., and Guice, L. K. (1995). “Buckling of encased elliptic thin ring.” J. Eng. Mech., 121(12), 1325–1329.
Lo, K. H., and Zhang, J. Q. (1994). “Collapse resistance modeling of encased pipes.” Buried plastic pipe technology, ASTM STP1222, D. Eckstein, ed., American Society for Testing and Materials, Philadelphia, Vol. 2.
Terzaghi, K. (1936). “Stress distribution in dry and saturated sands above a yielding trap door.” Proc., 1st Int. Conf. in Soil Mechanics and Foundations Engineering.
Information & Authors
Information
Published In
Copyright
© 2005 ASCE.
History
Received: Jan 6, 2003
Accepted: Dec 7, 2004
Published online: Sep 1, 2005
Published in print: Sep 2005
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.