Context-Sensitive Design: Issues with Design Elements
Publication: Journal of Transportation Engineering
Volume 131, Issue 5
Abstract
Well-designed roadways should equally consider and address safety, mobility, and community needs. The concept of context sensitive design is an emerging project development and geometric design approach that aims to meet the objectives of these elements. Central to the design process is the selection of key design elements that have the potential to influence design choices and roadway elements. Design speed is probably the most influential factor and current practices on how this speed is selected and used may need to be revisited. The need to design a roadway that could provide all required clues to the driver in order to drive at desired operating speeds is also an issue that requires attention. Design consistency along with compatibility between design and operating speed feature prominent among the issues that should be considered within the context sensitive design. This paper focuses on various design elements and discusses their relevance, importance, and influence on context sensitive design.
Get full access to this article
View all available purchase options and get full access to this article.
References
Agent, K. R., and Pigman, J. G. (2001). “Safety impacts of rural road construction.” Rep. No. KTC-01-01, Kentucky Transportation Center, Lexington, Ky.
American Association of State Highway Transportation Officials (AASHTO). 1984). A policy on geometric design of highways and streets, Washington, D.C.
American Association of State Highway Transportation Officials (AASHTO). (2001). A policy on geometric design of highways and streets, Washington, D.C.
Council, F. M., and Stewart, R. (1999). “Safety effects of the conversion of rural two-lane to four-lane roadways based on cross-sectional models.” Transportation Research Record 1665, Transportation Research Board, Washington, D.C., 35–43.
Elvik, R. (2003). “Effects of roadway safety of converting intersections to roundabouts: Review of evidence from non-U.S. studies.” Transportation Research Record 1847, Transportation Research Board, Washington, D.C., 1–10.
Federal Highway Administration (FHWA). (1997). “Flexibility in highway design.” FHWA-PD-97-062, Washington, D.C.
Federal Highway Administration (FHWA). (2000) “Roundabouts: An informational guide.” FHWA-RD-00-67, FHWA, Washington, D.C.
Harwood, D., Neuman, T., and Leisch, J. (2000). “Summary of design speed, operating speed, and design consistency issues.” J. Transp. Res. Board, 1701, 116–120.
Hauer, E. (2000). “Safety in geometric design standards I and II.” Conf. Proc., 2nd Int. Symp. on Highway Geometric Design, Mainz, Germany.
Krammes, R. (2000). “Design speed and operating speed in rural highway alignment design.” J. Transp. Res. Board, 1701, 68–75.
Krammes, R. A., and Glasscock, S. W. (1992). “Geometric inconsistencies and accident experience on two-lane rural highways.” Transportation Research Record 1356, Transportation Research Board, Washington, D.C., 1–10.
Poe, C. M., Tarris, J. M., and Mason, J. M. (1996). “Relationship of operating speeds to roadway geometric design speeds.” PTI Rep. No. 9606, Pennsylvania Transportation Institute, State College, Pa.
Stamatiadis, N. et al. (2000). “International scanning tour on highway geometric design.” FHWA-PL-01-026, Federal Highway Administration, Washington, D.C.
Stamatiadis, N., Jones, S., and Aultman-Hall, L. (1999). “Causal factors for accidents on southeast low-volume roads.” Transportation Research Record 1652, Transportation Research Board, Washington, D.C., 111–117.
Transportation Research Board (TRB). (1987a). “Designing safer roads; Practices for resurfacing, restoration, and rehabilitation.” Special Rep. No. 214, Transportation Research Board, Washington, D.C.
Transportation Research Board (TRB). (1987b). “Relationship between safety and key highway features: A synthesis of prior research.” State of the Art Rep. No. 6, Transportation Research Board, Washington, D.C.
United States Department of Transportation, Federal Highway Administration (USDOT/FHWA). (1974). Highway functional classification: Concepts, criteria, and procedures, USDOT/FHWA, Washington, D.C.
Zegeer, C., and Deacon, J. (1987). “Effect of lane width, shoulder width, and shoulder type on highway safety.” State of the Art Rep. No. 6, Transportation Research Board, Washington, D.C., 1–21.
Zegeer, C., Stewart, R., Council, F., and Neuman, T. (1994). “Accident relationships of roadway width on low-volume roads.” Transportation Research Record 1445, Transportation Research Board, Washington, D.C., 160–168.
Information & Authors
Information
Published In
Copyright
© 2005 ASCE.
History
Received: Mar 5, 2004
Accepted: Oct 20, 2004
Published online: May 1, 2005
Published in print: May 2005
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.