Method for Balancing Cut-Fill and Minimizing the Amount of Earthwork in the Geometric Design of Highways
Publication: Journal of Transportation Engineering
Volume 129, Issue 5
Abstract
In highway projects, economic considerations are as important as other design controls and elements of design. As a result, the highway designer should consider cut and fill balance along with minimizing earthwork which may significantly decrease construction costs. In practice, one way to reduce the amount of earthwork is to set the grade line as closely as possible to the ground line while also considering cut and fill balance. However, this practice may be misleading since balancing is achieved along the centerline of the road. In reality, the centerline ground elevation rarely represents the whole cross section in terms of cut and fill balancing. Especially in mountainous terrain, transverse changes in ground elevation with respect to the centerline elevation of cross section are abrupt. The aim of this paper is to propose a method that considers a hypothetical “weighted ground elevation” representing the average of transverse changes in the ground elevation rather than the elevation at the centerline. Consequently, conforming the grade line to the weighted ground line (integration of the weighted ground elevations along the centerline) would give balanced cut and fill and lesser amount of earthwork, resulting in a much more cost effective result.
Get full access to this article
View all available purchase options and get full access to this article.
References
AASHTO. (1994). “A policy on geometric design of highways and streets.” AASHTO Publication, Washington, D.C.
Abbey, L. (1992). Highways, Van Nostrand Reinhold, New York.
AUSTROADS Guide. (1993). “Rural road design.” Guide to the geometric design of rural roads, AUSTROADS Publication AP-1/89, Sydney, Australia.
Banks, J. H. (1998). Introduction to transportation engineering, WCB/McGraw-Hill Company, Singapore.
Batson, R. G., and Proudlove, J. A. (1968). Roads, Longmans, Green and Co. Ltd., London.
Bruce, A. G., and Clarkson, J. (1950). Highway design and construction, International Textbook Company, Scranton, Pa.
CALTRANS. (1995). Highway design manual, California Department of Transportation Publication, Sacramento, Calif., 200/1–58.
Davis, T. G.(1994). “Finite-element volumes.” J. Surv. Eng., 120(3), 94–114.
Easa, S. M.(1988). “Estimating pit excavation volume using nonlinear ground profile.” J. Surv. Eng., 114(2), 71–83.
Easa, S. M.(1991). “Pyramid frustum formula for computing volumes at roadway transition areas.” J. Surv. Eng., 117(2), 98–101.
Easa, S. M.(1998). “Smooth surface approximation for computing pit excavation volume.” J. Surv. Eng., 124(3), 125–133.
Easa, S. M.(1999). “Optimum vertical curves for highway profiles.” J. Surv. Eng., 125(3), 147–157.
Garber, N. J., and Hoel, L. A. (1988). Traffic and highway engineering, West Publishing Company, St. Paul, Minn.
Gibreel, G. M., Easa, S. M., Hassan, Y., and El-Dimeery, I. A.(1999). “State of art of highway geometric design consistency.” J. Transp. Eng., 125(4), 305–313.
Hassan, Y., Easa, S. M., and Abd El Halim, A. O.(1997). “Design considerations for combined highway alignments.” J. Transp. Eng., 123(1), 60–68.
Hickerson, T. F. (1959). Road surveys and design, McGraw-Hill, New York.
Krammes, R. A., and Granham, M. A. (1995). “Worldwide review of alignment design policies.” Proc., 1st Int. Symp. on Highway Geometric Design Practices, Boston, Transportation Research Board, Washington, D.C., 19-1–19-17.
Mannering, F. L., and Kilareski, W. P. (1990). Principles of highway engineering and traffic analysis, Wiley, New York.
NETCAD-NETPRO v2.95. (1999). Software manual, Ak Engineering Publication, Ankara, Turkey.
Oglesby, C. H., and Hicks, R. G. (1982). Highway engineering, Wiley, Toronto.
Papacostas, C. S., and Prevedouros, P. D. (1993). Transportation engineering and planning, Prentice-Hall, Englewood Cliffs, N.J.
Schoon, J. G. (1993). Geometric design projects for highways: An introduction, ASCE, New York.
Sthapit, N., and Mori, H.(1994). “Model to estimate highway earthwork cost in Nepal.” J. Transp. Eng., 120(3), 498–504.
Taiganidis, I., and Kanellaidis, G.(1999). “Approximate perspective design of roads.” J. Transp. Eng., 125(4), 314–323.
Information & Authors
Information
Published In
Journal of Transportation Engineering
Volume 129 • Issue 5 • September 2003
Pages: 564 - 571
Copyright
Copyright © 2003 American Society of Civil Engineers.
History
Received: Aug 2, 2000
Accepted: Jul 31, 2002
Published online: Aug 15, 2003
Published in print: Sep 2003
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.