Establishing Practical Approach for Design Consistency Evaluation
Publication: Journal of Transportation Engineering
Volume 127, Issue 4
Abstract
The concept of design consistency has lately been gaining greater acceptance in North America. Considerable research work is being carried out and steps have already been taken to incorporate this concept into the design practices in Canada and the United States. However, a standard procedure that can be followed by designers to evaluate the design consistency of new or existing alignments is still lacking. This paper compiles different measures for evaluating geometric design consistency, as presented in available research work, to identify their potential applicability and any required future research. These consistency measures are operating speed, vehicle stability, alignment indices, and driver workload. Four fictitious alignments were presented and subjected to these measures in a step-by-step exercise of consistency evaluation. A relationship between design consistency measures and safety, which is the main objective of the design consistency concept, is also discussed. Overall, consistency measures were successful in identifying inconsistencies in the proposed alignments. However, the exercise showed the need for more research work in a number of areas for complete and accurate consistency evaluation.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
American Association of State Highway Transportation Officials (AASHTO). ( 1994). A policy on geometric design of highways and streets, Washington, D.C.
2.
Anderson, I. B., Bauer, K. M., Harwood, D. W., and Fitzpatrick, K. ( 1999). “Relationship to safety of geometric design consistency measures for rural two-lane highways.” Transp. Res. Rec. 1658, Transportation Research Board, Washington, D.C., 43–51.
3.
Bonneson, J. A. (1999). “Side friction and speed as controls for horizontal curve design.”J. Transp. Engrg., ASCE, 125(6), 473–480.
4.
Brenac, T. ( 1996). “Safety at curves and road geometry standards in some European countries.” Transp. Res. Rec. 1523, Transportation Research Board, Washington, D.C., 99–106.
5.
British Columbia Ministry of Transportation and Highways (MoTH). ( 1994). Highway engineering design manual, Victoria, B.C., Canada.
6.
Fitzpatrick, K., and Collins, J. M. ( 2000). “Speed-profile model for two-lane rural highways.” Transp. Res. Rec. 1737, Transportation Research Board, Washington, D.C., 42–49.
7.
Fitzpatrick, K., Krammes, R. A., and Fambro, D. B. ( 1997). “Design speed, operating speed, and posted speed relationships.” Inst. of Transp. Engrs. J., 67(2), 52–59.
8.
Gibreel, G., Easa, S. M., and Al-Dimeery, I. A. (2001). “Prediction of operating speed on three-dimensional highway alignments.”J. Transp. Engrg., ASCE, 127(1), 21–30.
9.
Gibreel, G. M., Easa, S. M., Hassan, Y., and El-Dimeery, I. A. (1999). “State of the art of highway geometric design consistency.”J. Transp. Engrg., ASCE, 125(4), 305–313.
10.
Hassan, Y., Gibreel, G. M., and Easa, S. M. (2000). “Evaluation of highway consistency and safety: Practical approach.”J. Transp. Engrg., ASCE, 126(3), 193–201.
11.
Kanellaidis, G. (1996). “Human factors in highway geometric design.”J. Transp. Engrg., ASCE, 122(1), 59–66.
12.
Krammes, R. A. ( 1997). “Interactive highway safety design model: Design consistency module.” Public Rd., 61(2), 47–52.
13.
Krammes, R. A., Rao, K. S., and Oh, H. ( 1995). “Highway geometric design consistency evaluation software.” Transp. Res. Rec. 1500, Transportation Research Board, Washington, D.C., 19–24.
14.
Lamm, R., Choueri, E. M., Hayward, J. C., and Paluri, A. ( 1988). “Possible design procedures to promote design consistency in highway geometric design of two-lane rural roads.” Transp. Res. Rec. 1195, Transportation Research Board, Washington, D.C., 111–122.
15.
Lamm, R., Choueri, E. M., and Mailaender, T. ( 1991). “Side friction demand versus side friction assumed for curve design on two-lane rural highways.” Transp. Res. Rec. 1303, Transportation Research Board, Washington, D.C., 11–21.
16.
Lamm, R., Guenther, A. K., and Choueri, E. M. ( 1995). “Safety module for highway geometric design.” Transp. Res. Rec. 1512, Transportation Research Board, Washington, D.C., 7–15.
17.
Lamm, R., Psarianos, B., and Mailaender, T. ( 1999). Highway design and traffic safety engineering handbook, McGraw-Hill, New York.
18.
Leish, J. E., and Leish, J. P. ( 1977). “New concepts in design speed application.” Transp. Res. Rec. 631, Transportation Research Board, Washington, D.C., 4–14.
19.
Al-Masaeid, H. R., Hamed, M., Aboul-Ela, M., and Ghannam, A. G. ( 1994). “Consistency of horizontal alignment for different vehicle classes.” Transp. Res. Rec. 1500, Transportation Research Board, Washington, D.C., 178–183.
20.
Morrall, J., and Talarico, R. J. ( 1994). “Side friction demanded and margins of safety on horizontal curves.” Transp. Res. Rec. 1435, Transportation Research Board, Washington, D.C., 145–152.
21.
Nicholson, A. (1998). “Superelevation, side friction, and roadway consistency.”J. Transp. Engrg., ASCE, 124(5), 411–418.
22.
Polus, A., Fitzpatrick, K., and Fambro, D. B. ( 2000). “Predicting operating speeds on tangent sections of two-lane rural highways.” Transp. Res. Rec. 1737, Transportation Research Board, Washington, D.C., 50–57.
23.
Parma, K., Fitzpatrick, K., and Krammes, R. ( 1999). “Predicting speed on tangents using alignment indices.” Proc., 78th Annu. Meeting of the Transp. Res. Board, Transportation Research Board, Washington, D.C.
24.
Polus, A., Poe, C. M., and Mason, J. M. ( 1995). “Review of international design speed practices in roadway geometric design.” Proc., Int. Symp. on Hwy. Geometric Des. Pract., Transportation Research Board, Washington, D.C., 5:1–5:8.
25.
Transport Canada. ( 1999). Canadian motor vehicle traffic collision statistics. Ottawa, ON, Canada.
26.
Transportation Association of Canada (TAC). ( 1999). Geometric design guide for Canadian roads, Ottawa.
27.
Wooldridge, M. D., Bauer, K., Green, P., and Fitzpatrick, K. ( 2000a). “Comparison of driver visual demand in test track, simulator, on-road environments.” Proc., 79th Annu. Meeting of the Transp. Res. Board, Transportation Research Board, Washington, D.C.
28.
Wooldridge, M. D., Fitzpatrick, K., Koppa, R., and Bauer, K. ( 2000b). “Effects of horizontal curvature on driver visual demand.” Transp. Res. Rec. 1737, Transportation Research Board, Washington, D.C., 71–77.
Information & Authors
Information
Published In
History
Received: Aug 18, 2000
Published online: Aug 1, 2001
Published in print: Aug 2001
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.