Modeling Indirect Statistics of Surface Roughness
Publication: Journal of Transportation Engineering
Volume 127, Issue 2
Abstract
Quarter-car model-based indirect statistics of road surface roughness are analyzed in this paper. The stochastic process theory is used to establish the relationship between the international roughness index (IRI) statistic of a quarter-car response and the power spectral density (PSD) of road random excitation. Under the circumstance of a linear vehicle model and homogeneous roughness with a zero-mean Gaussian distribution, we prove that the average of the absolute response of the quarter-car model is directly proportional to the standard deviation of that response quantity. This result enables us to further correlate the indirect statistics with PSD roughness. A theoretical relation between the IRI and the PSD roughness is established. Based on the road classification proposed by the International Standards Organization (ISO), it is found that a linear correlation exists between the IRI and the standard deviation of roughness. Furthermore, corresponding to the ISO PSD-based road classification, an IRI-based road classification is provided to categorize pavement into five classes, ranging from very good surface condition to very poor surface condition.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Carey, W. N., and Irick, P. E. ( 1960). “The pavement serviceability—Performance concept.” Hwy. Res. Bull., Highway Research Board, New Delhi, 250.
2.
Casella, G., and Berger, R. L. ( 1990). Statistical inference, Brooks/Cole, Pacific Grove, Calif.
3.
Cebon et al. ( 1993). “Effects of heavy-vehicle characteristics on pavement response and performance.” Nat. Cooperative Hwy. Res. Program Res. Rep. No. 353, Transportation Research Board, National Research Council, Washington, D.C.
4.
Dodds, C. J. ( 1974). “The laboratory simulation of vehicle service stress.” J. Engrg. for Industry, 2, 391–398.
5.
Dodds, C. J., and Robson, J. D. ( 1973). “The description of road surface roughness.” J. Sound and Vibration, 31, 175–183.
6.
Gillespie, T. D., Sayers, M. W., and Segel, L. ( 1980). “Calibration of response-type road roughness measuring systems.” Nat. Cooperative Hwy. Res. Program Res. Rep. No. 228, Transportation Research Board, National Research Council, Washington, D.C.
7.
Haas, R., Hudson, W. R., and Zaniewski, J. ( 1994). Modern pavement management, Krieger, Melbourne, Fla.
8.
Heath, A. N., and Good, M. G. ( 1985). “Heavy vehicle design parameters and dynamic pavement loading.” Australian Road Res., 15(4), 209–217.
9.
Hedric, J. K., and Markow, M. ( 1985). “Predictive models for evaluating load impact factors of heavy trucks on current pavement conditions.” Interim Rep. Prepared for U.S. Dept. of Transp., Ofc. of Univ. Res., DTES5684-C-0001, Massachusetts Institute of Technology.
10.
Hudson, W. R. ( 1985). “Root-mean-square vertical acceleration as a summary of roughness statistics.” ASTM Spec. Tech. Publ. No. 884, T. D. Gillespie and M. Sayers, eds., ASTM, West Conshohocken, Pa.
11.
International Standards Organization (ISO). ( 1972). “PSI proposals for generalized road inputs to vehicles.” ISO/TC 180/WG 9, Geneva.
12.
Janoff, M. S. ( 1988). “Pavement roughness and rideability field evaluation.” Nat. Cooperative Hwy. Res. Program Res. Rep. No. 308, Transportation Research Board, National Research Council, Washington, D.C.
13.
Janoff, M. S., Nick, J. B., Davit, P. S., and Hayhoe, G. F. ( 1985). “Pavement roughness and rideability.” Nat. Cooperative Hwy. Res. Program Res. Rep. No. 275, Transportation Research Board, National Research Council, Washington, D.C.
14.
Marcondes, J. A., Snyder, M. B., and Singh, S. P. (1992). “Predicting vertical acceleration in vehicles through road roughness.”J. Transp. Engrg., ASCE, 118(1), 33–49.
15.
Monismith, C. L., Sousa, J., and Lysmer, J. ( 1988). “Modern pavement design technology including dynamic load conditions.” Trans., SAE, SP-765 (881856), Warrendale, Pa.
16.
Newland, D. E., (1984). ( 1984). An introduction to random vibration and spectral analysis, 2nd Ed., Longman's, London.
17.
Phillips, M. B., and Swift, G. ( 1969). “A comparison of four roughness measuring systems.” Hwy. Res. Rec., 291, 227–235.
18.
Robson, J. D. ( 1979). “Road surface description and vehicle response.” Int. J. Vehicle Des., 1(1), 21–25.
19.
Sayers, M. ( 1985). “Development, implementation, and application of the reference quarter-car simulation.” ASTM Spec. Tech. Publ. No. 884, T. D. Gillespie and M. Sayers, eds., ASTM, West Conshohocken, Pa.
20.
Vol. 04.03, ASTM, West Conshohocken, Pa.
21.
Sun, L. ( 1998). “Theoretical investigations on vehicle-ground dynamic interaction.” Final. Rep. Prepared for Nat. Sci. Found. of China, Southeast University, Nanjing, China.
22.
Sun, L., and Deng, X. ( 1997). “Transient response for infinite plate on Winkler foundation by a moving distributed load.” Chinese J. Appl. Mech., Xi'an, China, 14(2), 72–78.
23.
Sun, L., and Deng, X. (1998). “Predicting vertical dynamic loads caused by vehicle-pavement interaction.”J. Transp. Engrg., ASCE, 124(5), 407–478.
24.
Sweatman, P. F. ( 1983). “A study of dynamic wheel forces in axle group suspensions of heavy vehicles.” Spec. Rep. No. 27, Australian Road Research Board.
25.
Wei, K. ( 1988). Vehicle dynamics, Renming Jiaotong, Beijing.
26.
Woodrooffe, R., and LeBlanc, P. A. ( 1986). “The influence of suspension variations on dynamic wheel loads of heavy vehicles.” SAE Tech. Paper. No. 861973, Society of Automotive Engineers, Warrendale, Pa.
27.
Zhu, W. Q. ( 1992). Random vibration, Academic, Beijing.
Information & Authors
Information
Published In
History
Received: Dec 22, 1999
Published online: Apr 1, 2001
Published in print: Apr 2001
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.