Design Considerations of Sight Distance Red Zones on Crest Curves
Publication: Journal of Transportation Engineering
Volume 124, Issue 4
Abstract
The American Association of State Highway and Transportation Officials (AASHTO) presents general controls for the combination of horizontal and vertical alignments. Excellence in alignment coordination enhances safety, operation, and appearance. This paper quantifies one of the AASHTO general controls that is related to introducing a horizontal curve at or near the top of a crest vertical curve. It establishes the locations where a horizontal curve should not start in relation to a vertical curve because the available sight distance is less than (1) the stopping-sight distance (SSD); or (2) the preview sight distance (PVSD) that allows the driver to detect the horizontal curve and react properly and comfortably. The range of these locations, called the “red zone,” is established for a selected alignment using three-dimensional (3D) analysis of sight distance. Both daytime and nighttime cases are discussed. The sensitivity of the red zones for PVSD to the superelevation rate, turning direction of horizontal curve, vertical curvature, and spiral curves is examined. The effect of spiral curves and location of cut slopes on the red zone for daytime SSD is also examined. This paper shows how 3D analysis can be used to identify red zones for existing combined alignments or to avoid them for new alignments. As such, it should be of interest to the design engineers concerned with highway safety.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
A policy on geometric design of highways and streets. (1994). Am. Assn. of State Hwy. and Transp. Officials (AASHTO), Washington, D.C.
2.
Easa, S. M. (1994). “Design considerations for highway sight-hidden dips.”J. Transp. Res., 28A(1), 17–29.
3.
Easa, S. M. (1995). “Geometric design.”Civil engineering handbook, W. F. Chen (ed.), CRC Press, Inc., Boca Raton, Fla.
4.
Easa, S. M., Abd El Halim, A. O., and Hassan, Y.(1996). “Sight distance evaluation on complex highway vertical alignments.”Can. J. of Civ. Engrg., 23(3), 577–586.
5.
Gattis, J. L., and Duncan, J.(1995). “Geometric design for adequate operational preview of road ahead.”Transp. Res. Record, 1500, 139–145.
6.
Hassan, Y., and Easa, S. M.(1997). “Design of sag vertical curves in three-dimensional alignments.”J. Transp. Engrg., ASCE, 124(1), 52–58.
7.
Hassan, Y., Easa, S. M., and Abd El Halim, A. O. (1995). “New development for establishing no-passing zones on two-lane highways due to vertical alignments.”Proc., Can. Soc. for Civ. Engrg., Montreal, Que., Canada, IV, 205–214.
8.
Hassan, Y., Easa, S. M., and Abd El Halim, A. O.(1996). “Analytical model for sight distance analysis on 3-D highway alignments.”Transp. Res. Record, 1523, 1–10.
9.
Hassan, Y., Easa, S. M., and Abd El Halim, A. O.(1997a). “Design considerations for combined highway alignments.”J. Transp. Engrg., ASCE, 123(1), 60–68.
10.
Hassan, Y., Easa, S. M., and Abd El Halim, A. O.(1997b). “Automation of marking passing and no-passing zones on two-lane highways.”Can. J. Civ. Engrg., 24(2), 263–275.
11.
Hassan, Y., Easa, S. M., and Abd El Halim, A. O.(1997c). “Modelling headlight sight distance on 3-D highway alignments.”Transp. Res. Record, 1579, 79–88.
12.
Highway design guide. (1995). French Admin. for the Tech. Studies of Roads and Motorways, Paris, France.
13.
Manual of geometric design standards for Canadian roads. (1986). Transp. Assn. of Canada (TAC), Ottawa, Canada.
Information & Authors
Information
Published In
Copyright
Copyright © 1998 American Society of Civil Engineers.
History
Published online: Jul 1, 1998
Published in print: Jul 1998
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.