Resilient Moduli of Granular Materials
Publication: Journal of Transportation Engineering
Volume 120, Issue 6
Abstract
The six most commonly encountered aggregates that are used as subbases/bases of roadways in Oklahoma were selected and tested under cyclic loading to evaluate the Resilient Modulus (RM) by using the AASHTO T292‐91I and T294‐92I methods. The gradation of the specimens met the Oklahoma Department of Transportation 1988 specifications for type A (fine) and type B (coarse) materials. A series of exploratory tests were performed to assess the effect of gradation, compaction method, specimen size, and testing procedures on the RM values. The values reported or suggested by various agencies were compared with the values obtained from the present study. Statistical correlations were established between RM and the California bearing ratio, and between RM and cohesion and friction angle. It was observed that, for a given gradation and bulk stress, the RM values obtained in this study were slightly lower than those reported in the literature; the influence of gradation and compaction method on RM values were less significant compared to the effects of the stress state. Higher RM values were obtained from the T294‐92I testing procedure than those obtained by the T292‐91I testing procedure. The RM values for 10.16‐cm specimens were higher than those for 15.24‐cm specimens, and a satisfactory correlation did exist between the RM values and the cohesion and friction angle.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
“AASHTO Guide for Design of Pavement.” (1986). American Association of State Highway and Transportation Officials (AASHTO), Washington, D.C.
2.
Coffman, B. S., Kraft, D. G., and Tamayo, J. (1964). “A comparison of calculated and measured deflections for the AASHTO test road.” Proc., Assoc. of Asphalt Paving Technologists.
3.
Hicks, R. G. (1970). “Factors influencing the resilient properties of granular materials,” PhD thesis, University of California, Berkeley, Calif.
4.
Ho, R. K. H. (1989). “Repeated load tests on untreated soils, a Florida experience.” Rep. No. FHWA‐TS‐90‐031, National Technical Information Service, Springfield, Va.
5.
Jackson, N. C. (1989). “Thought on AASHTO T‐274‐82, resilient modulus of subgrade soils.” Rep. No. FHWA‐TS‐90‐031, National Technical Information Service, Springfield, Va.
6.
“Interim method of test for resilient modulus of subgrade soils and untreated base/subbase materials.” (1991). AASHTO Designation T292‐91I. American Association of State Highway and Transportation Officials (AASHTO), Washington, D.C.
7.
“Interim method of test for resilient modulus of unbound granular base/subbase materials and subgrade soils‐SHRP protocol P46.” (1992). AASHTO Designation T294‐92I. American Association of State Highway and Transportation Officials (AASHTO), Washington, D.C.
8.
Laguros, J., Zamm, M. M., and Chen, D.‐H. (1993). “Resilient modulus of select aggregate bases and their correlations with other engineering properties.” Rep. No. 2189, ORA 125‐6073. School of Civ. Engrg. and Envir. Sci., University of Oklahoma, Norman, Okla.
9.
May, R. W., and Witczak, W. M. (1981). “Effective granular modulus to model pavement responses.” Transp. Res. Record No. 810, Transportation Research Board, Washington, D.C., 1–17.
10.
Pezo, R. F., Claros, G., Hudson, W. R., and Stoke, K. H. (1992). “Development of a reliable resilient modulus test for subgrade and non‐granular subbase materials for use in routine pavement design.” Res. Rep. 1177‐4f, Proj. 2/3/10‐8‐88/0‐1177, Ctr. for Transp. Res., Bureau of Engrg. Res., University of Texas, Austin, Tex., January.
11.
Rada, C., and Witczak, W. M. (1981). “Comprehensive evaluation of laboratory resilient moduli results for granular material.” Transp. Res. Record No. 810, Transportation Research Board, Washington, D.C., 23–33.
12.
“Standard method of test for the California bearing ratio.” (1986). AASHTO Designation T193‐81. American Association of State Highway and Transportation Officials (AASHTO), Washington, D.C.
13.
“Standard method of test for resilient modulus of subgrade soils.” (1986). AASHTO Designation T274‐82. American Association of State Highway and Transportation Officials (AASHTO), Washington, D.C.
14.
“Standard method of test for sieve analysis of fine and coarse aggregates.” (1986). AASHTO Designation T27‐84. American Association of State Highway and Transportation Officials (AASHTO), Washington, D.C.
15.
“Standard specifications for highway construction.” (1988). Oklahoma Department of Transportation (ODOT), Oklahoma City, Okla.
16.
“Thickness design—asphalt pavements for highways and streets.” (1981). Manual Series No. 1 (MS‐1), Asphalt Institute (AI), Lexington, Ky.
17.
Thompson, M. R. (1989). “Factors affecting the resilient moduli of soil and granular materials.” Rep. No. FHWA‐TS‐90‐031, National Technical Information Service, Springfield, Va.
18.
Thompson, M. R., and Smith, K. L. (1990). “Repeated triaxial characterization of granular bases.” Transp. Res. Record No. 1278, Transportation Research Board, Washington, D.C., 7–17.
19.
Vinson, T. S. (1989). “Fundamentals of resilient modulus testing.” Rep. No. FHWA‐TS‐90‐031, National Technical Information Service, Springfield, Va.
20.
Zaman, M. M., Laguros, J., and Danayak, R. (1991). “Assessment of resilient modulus testing methods and their application to design of pavements.” Rep. No. FHWA/OK 91(08), University of Oklahoma, Norman, Okla.
Information & Authors
Information
Published In
Copyright
Copyright © 1994 American Society of Civil Engineers.
History
Received: Oct 5, 1993
Published online: Nov 1, 1994
Published in print: Nov 1994
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.