Performance of Steel Fibrous Reinforced Concrete Corbels Subjected to Vertical and Horizontal Loads
Publication: Journal of Structural Engineering
Volume 135, Issue 5
Abstract
A softened strut-and-tie macromodel able to reproduce the flexural behavior of corbels in plain and fibrous concrete and with the presence of steel bars, including softening of compressed struts and yielding of main and secondary steel bars, is presented in this paper. The main focus of the proposed model is the determination of the load-deflection curves of corbels subjected to the coupled effects of vertical and horizontal forces bearing in mind the influence of the type of concrete (normal or high strength), of the fiber percentage and of the arrangement and percentage of the main and secondary (horizontal stirrup) steel bars. A validation of the proposed model is made therefore with reference to some of the experimental data available in the literature and also to numerical results obtained by using a nonlinear finite-element program (ATENA-2D) able to analyze the flexural behavior of deep members. Finally some design considerations on the use of fibrous reinforced concrete in RC corbels are given.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Support of this research by the Ministero dell’Istruzione, dell’Università e della Ricerca is gratefully acknowledged.
References
American Concrete Institute (ACI). (2002). “Building code requirements for reinforced concrete.” ACI 318-95, and “Commentary.” ACI 318RM-02, ACI Committee 318, Detroit.
Campione, G. (2008). “Simplified flexural response of fibrous concrete beams.” J. Mater. Civ. Eng., 20(4), 283–293.
Campione, G., La Mendola, L., and Mangiavillano, M. L. (2007). “Steel fibers reinforced concrete corbels: Experimental behaviour and shear strength prediction.” ACI Struct. J., 104(5) 570–579.
Campione, G., La Mendola, L., and Papia, M. (2005). “Flexural behaviour of concrete corbels containing steel fibers or wrapped with FRP sheets.” Mater. Struct., 38(280), 617–625.
Cervenka, V. (2000). “Simulating a response.” Concrete Engineering International, 4(4), 45–49.
Chen, G. (1988). “Plastic analysis of shear in beams, deep beams and corbels.” Rep. No. R-273, Dept. of Structural Engineering, Technical Univ. of Denmark, Copenhagen, Denmark.
Collins, M. P., and Michell, D. (1986). “Rational approach to shear design-the 1984 Canadian code provisions.” ACI Struct. J., 83(6), 925–933.
Eurocodice 2. (1992). “Ingegneria strutturale.” Progettazione delle strutture di calcestruzzo (UNI ENV 1992–1-1), Commissione Milano Italy (in Italian).
Fattuhi, N. I. (1987). “SFRC corbel tests.” ACI Struct. J., 84(2), 119–651.
Fattuhi, N. I. (1990). “Strength of SFRC corbels subjected to vertical load.” ACI Struct. J., 116(3), 701–718.
Fattuhi, N. I. (1994a). “Strength of FRC corbels in flexure.” J. Struct. Eng., 120(2), 360–377.
Fattuhi, N. I. (1994b). “Reinforced corbels made with plain and fibrous concretes.” ACI Struct. J., 91(5), 530–536.
Fattuhi, N. I., and Hughes, B. P. (1989a). “Reinforced steel fiber concrete corbels with various shear span-to-depth ratios.” ACI Struct. J., 86(6), 590–596.
Fattuhi, N. I., and Hughes, B. P. (1989b). “Ductility of reinforced concrete corbels containing either steel fibers or stirrups.” ACI Struct. J., 86(6), 644–651.
Foster, S. J., and Malik, A. R. (2002). “Evaluation of efficiency factor models used in strut-and-tie modeling of nonflexural members.” J. Struct. Eng., 128(5), 569–577.
Foster, S. J., Powell, R. E., and Selim, H. S. (1996). “Performance of high-strength concrete corbels.” ACI Struct. J., 93(5), 555–563.
Hwang, S., and Lee, H. (2002). “Strength prediction for discontinuity regions by softened strut and tie model.” J. Struct. Eng., 128(12), 1519–1526.
Hwang, S., Lu, W., and Lee, H. (2000). “Shear strength prediction for reinforced concrete corbels.” ACI Struct. J., 97(4), 543–552.
Mansur, M. A., and Ong, K. C. G. (1991). “Behavior of reinforced fiber concrete deep beams in shear.” ACI Struct. J., 88(1), 98–105.
Russo, G., Venir, R., Pauletta, M., and Somma, G. (2006). “Reinforced concrete corbels shear strength model and design formula.” ACI Struct. J., 103(1), 3–7.
Solanki, H., and Sabnis, G. M. (1987). “Reinforced concrete corbels-simplified.” ACI Struct. J., 84(5), 428–432.
Warwick, W. B., and Foster, S. J., (1993). “Investigation into the efficiency factor used in non flexural reinforced concrete members design.” UNICIV Rep. No. R-320, School of Civil Engineering, Univ. of New South Wales, Kensington, Sydney, Australia.
Yong, Y., and Balaguru, P. (1994). “Behaviour of reinforced high-strength-concrete corbels.” J. Struct. Eng., 120(4), 1182–1201.
Zhang, L. X., and Hsu, T. T. C. (1998). “Behaviour and analysis of concrete membrane elements.” J. Struct. Eng., 124(1), 24–34.
Information & Authors
Information
Published In
Copyright
© 2009 ASCE.
History
Received: May 25, 2007
Accepted: Nov 27, 2008
Published online: May 1, 2009
Published in print: May 2009
Notes
Note. Associate Editor: Dat Duthinh
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.