Behavior of Cylindrical Steel Shells Supported on Local Brackets
Publication: Journal of Structural Engineering
Volume 134, Issue 8
Abstract
The connection of a local support to an elevated cylindrical metal silo shell is a long-standing difficult problem in shell analysis, and most designs are based on simple ideas using past experiences of successes and failures. Smaller silo structures are often supported on local brackets attached to the side of the shell, but very few investigations of the behavior or strength of such an arrangement have ever been made. This paper presents an outline description of the behavior of a cylindrical steel shell that is discretely supported on several brackets, each rigidly connected to a stiff column or floor. The linear, materially nonlinear, geometrically nonlinear, and bifurcation behaviors of the shell under these conditions are outlined. In this problem the prebuckling deformations, bifurcation mode, and plastic collapse mode are each local. This configuration presents some interesting questions concerning the relative importance of geometric nonlinearity and geometric imperfections. The problem is recommended to advanced shell analysts as a benchmark test of their analysis and interpretation techniques.
Get full access to this article
View all available purchase options and get full access to this article.
References
Bijlaard, P. P. (1955). “Stresses from local loading in cylindrical pressure vessels.” Trans. ASME, 77, 805–816.
Cai, M., Holst, J. M. F. G., and Rotter, J. M. (2002). “Buckling strength of thin cylindrical shells under localized axial compression.” Proc., 15th Engineering Mechanics Conf., ASCE, Reston, Va.
DASt-Richtlinie. (1980) “Beulsicherheitsnachweise für Schalen.” DASt Richtlinie 013, Deutscher Ausschuss für Stahlbau, Köln, Germany.
Doerich, C. (2007). “Strength and stability of locally supported cylinders.” Ph.D. thesis, Univ. of Edinburgh, Edinburgh, U.K.
European Committee for Standardization (CEN). (2006). “Eurocode 3: Design of steel structures, Part 1.6: Strength and stability of shell structures.” EN1993-1-6, Brussels, Belgium.
Flügge, W. (1973). Stresses in shells, 2nd Ed., Springer, Berlin.
Gillie, M., Holst, J. M. F. G., Münch, M., and Rotter, J. M. (2002). “Behavior of silos supported on discrete brackets.” Int. J. Struct. Stab. Dyn., 2(1), 45–62.
Gould, P. L., Lowrey, R. D., Suryoutomo, H., Wang, R. S. C., and Sen, S. K. (1976). “Column supported cylindrical-conical tanks.” J. Struct. Div., 102(2), 429–447.
Greiner, R., and Guggenberger, W. (1998). “Buckling behavior of axially loaded steel cylinders on local supports—With and without internal pressure.” Thin-Walled Struct., 31, 159–167.
Guggenberger, W. (1991). “Buckling of cylindrical shells under local axial loads.” Proc., Int. Colloquium on Buckling of Shell Structures on Land, in the Sea and in the Air, Villeurbanne, Lyon, France, 323–333.
Guggenberger, W. (1998). “Proposal for design rules of axially loaded steel cylinders on local supports.” Thin-Walled Struct., 31(1–3), 169–185.
Guggenberger, W., Greiner, R., and Rotter, J. M. (2000). “The behavior of locally-supported cylindrical shells: Unstiffened shells.” J. Constr. Steel Res., 56(2), 175–197.
Hibbit, Karlsson & Sorensen Inc. (HKS). (2003). ABAQUS user’s manual, version 6.4, Pawntucket, R.I.
Holst, J. M. F. G., and Rotter, J. M. (2004). “Settlement beneath cylindrical shells.” Buckling of thin metal shells, J. G. Teng and J. M. Rotter, eds., Spon, London, 129–153.
Holst, J. M. F. G., Rotter, J. M., Gillie, M., and Münch, M. (2002). Failure criteria for shells on local supports.” New approaches to structural mechanics, shells and biological structures, H. R. Drew and S. Pellegrino, eds., Kluwer Academic, London, 315–327.
Kildegaard, A. (1969). “Bending of a cylindrical shell subjected to axial loading.” Proc., 2nd Symp. on Theory of Thin Shells, IUTAM, Copenhagen, Springer, Berlin, 301–315.
Li, H. Y., and Rotter, J. M. (1996). “Algebraic analysis of elastic circular cylindrical shells under local loadings (Part 1 and Part 2).” Int. Conf. on Advances in Steel Structures (ICASS ’96), Hong Kong, 801–814 and 808814, Elsevier Ltd., Oxford, U.K.
Massonnet, C. E., and Save, M. (1972). Plastic analysis and design of plates, shells and disks, North-Holland Publishing Co., Amsterdam, The Netherlands.
Nemeth, M. P., and Starnes, J. H. (1998). The NASA monographs on shell stability design recommendations—A review and suggested improvements, NASA TP 1998-206290, Langley Research Center, Hampton, Va.
Peter, J. (1974). “Zur stabilitat von Kreiscylinderschalen unter ungleichmaessig verteilten axialen randbelastungen.” Ph.D. thesis, Univ. of Hannover, Hannover, Germany.
Reissner, E. (1940). “Note on the problem of the distribution of stress in a thin stiffened elastic sheet.” Proc. Natl. Acad. Sci. U.S.A., 26, 300–305.
Rotter, J. M. (1998). “Shell structures: The new European standard and current research needs.” Thin-Walled Struct., 31(1–3), 3–23.
Rotter, J. M. (2003). “Buckling of shallow conical shell roofs for small diameter tanks and silos.” Int. Conf. on Design, Inspection, and Maintenance of Cylindrical Steel Tanks and Pipelines, Prague, Czech Republic, 169–175.
Rotter, J. M. (2004). “Buckling of cylindrical shells under axial compression.” Buckling of thin metal shells, J. G. Teng and J. M. Rotter, eds., Spon, London, 42–87.
Rotter, J. M., Teng, J. G., and Li, H. Y. (1991). “Buckling in thin elastic cylinders on column supports.” Proc., Int. Colloquium on Buckling of Shell Structures on Land, in the Sea and in the Air, Villeurbanne, Lyon, France, 334–343.
Teng, J. G., and Rotter, J. M. (1990). “A study of buckling in column-supported cylinders.” Contact loading and local effects in thin-walled plated and shell structures, V. Krupka and M. Drdacky, eds., Academia Press, Prague, Czechoslovakia, 52–61.
Teng, J. G., and Rotter, J. M. (1992). “Linear bifurcation of perfect column-supported cylinders—Support modeling and boundary conditions.” Thin-Walled Struct., 14(3), 241–263.
Timoshenko, S. P., and Goodier, J. N. (1970). Theory of elasticity, 3rd Ed., McGraw-Hill, New York.
Wang, R. S. C., and Gould, P. L. (1974). “Continuously supported cylindrical-conical tanks.” J. Struct. Div., 100(10), 2037–2052.
Yamaki, N. (1984). Elastic stability of circular cylindrical shells, Elsevier Applied Science Publishers, North Holland, Amsterdam, The Netherlands.
Information & Authors
Information
Published In
Copyright
© 2008 ASCE.
History
Received: Apr 2, 2007
Accepted: Jan 28, 2008
Published online: Aug 1, 2008
Published in print: Aug 2008
Notes
Note. Associate Editor: Benjamin W. Schafer
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.