Confinement Reinforcement Design for Reinforced Concrete Columns
Publication: Journal of Structural Engineering
Volume 134, Issue 5
Abstract
This paper presents new equations for the design of confinement reinforcement for ductile earthquake-resistant rectangular and circular columns based on performance measured in terms of curvature demand. These equations are developed from a parametric study of a large number of columns to reach a certain level of sectional ductility and account for the influence of concrete strength, transverse reinforcement yield strength, axial load level, and transverse confinement reinforcement spatial distribution. Simplification of these equations, while retaining the main controlling parameters, leads to design equations appropriate for design codes. These equations are then validated against a large set of experimental results. Their implementation in the Canadian Standard for Design of Concrete Structures is explained.
Get full access to this article
View all available purchase options and get full access to this article.
References
American Concrete Institute (ACI). (2005). “Building code requirements for structural concrete.” ACI No. 318-05, Farmington Hills, Mich.
American Society for Testing and Materials (ASTM). (2006). “Standard specification for deformed and plain carbon-steel bars for concrete reinforcement.” ASTM No. A615/A615M-06a, Philadelphia.
Atalay, M. B., and Penzien, J. (1975). “The seismic behavior of critical regions of reinforced concrete components as influenced by moment, shear, and axial force.” Rep. No. EERC 75-19, Earthquake Engineering Research Center, Univ. of California, Berkeley, Calif.
Azizinamini, A., Baum Kuska, S. S., Brungardt, P., and Hatfield, E. (1994). “Seismic behavior of square high-strength concrete columns.” ACI Struct. J., 91(3), 336–345.
Bayrak, O., and Sheikh, S. A. (1998). “Confinement reinforcement design consideration for ductile HSC columns.” J. Struct. Eng., 124(9), 999–1010.
Canadian Standard Association (CSA). (1994). “Design of concrete structures.” CSA No. A23.3-94, Rexdale, Canada.
Canadian Standard Association (CSA). (2004). “Design of concrete structures.” CSA No. A23.3-04, Mississauga, Canada.
Cusson, D., and Paultre, P. (1994). “High-strength concrete columns confined by rectangular ties.” J. Struct. Eng., 120(3), 783–804.
Konstantinidis, K. K., Kappos, A. J., and Izzuddin, B. A. (2007). “Analytical stress-strain model for high-strength concrete members under cyclic loading.” J. Struct. Eng., 133(4), 484–494.
Kunnath, S. K., El-Bahy, A., Taylor, A. W., and Stone, W. C. (1997). “Cumulative seismic damage of reinforced concrete bridge piers.” Rep. No. NISTIR 6075, National Institute of Standards and Technology, Gaithersburg, Md.
Légeron, F., and Paultre, P. (2000). “Behavior of high-strength concrete columns under cyclic flexure and constant axial load.” ACI Struct. J., 97(4), 591–601.
Légeron, F., and Paultre, P. (2003). “Uniaxial confinement model for normal and high-strength concrete columns.” J. Struct. Eng., 129(2), 241–252.
Lehman, D., Moehle, J., Mahin, S., Calderone, A., and Henry, L. (2004). “Experimental evaluation of the seismic performance of reinforced concrete bridge columns.” J. Struct. Eng., 130(6), 869–879.
Li, B., Park, R., and Brungardt, P. (2004). “Confining reinforcement for high-strength concrete columns.” ACI Struct. J., 101(3), 314–324.
Li, B., Park, R., and Tanaka, H. (1994). “Strength and ductility of reinforced concrete members and frames constructed using HSC.” Rep. No. 94-5, Dept. of Civil Engineering, Univ. of Canterbury, Christchurch, New Zealand.
Mander, J. B., Priestley, M. J. N., and Park, R. (1984). “Seismic design of bridge piers.” Rep. No. 84-2, Univ. of Canterbury, Christchurch, New Zealand.
National Research Council (NRC). (2005). “National building code of Canada 2005.” NBCC-05, Ottawa, Canada.
Paultre, P. (2001). “MNPHI: User manual.” CRGP Rep. No. 2001-01, Dept. of Civil Engineering, Univ. of Sherbrooke, Sherbrooke, Canada.
Paultre, P., Légeron, F., and Mongeau, D. (2001). “Influence of concrete strength and yield strength of ties on the behavior of high-strength concrete columns.” ACI Struct. J., 98(4), 490–501.
Richart, F. E., Brandtzaeg, A., and Brown, R. L. (1929). “A study of the failure of concrete under combined compressive stresses.” Bulletin No. 185, Engineering Experimental Station, Univ. of Illinois, Urbana Ill.
Robles, H. I., Bouaanani, N., and Paultre, P. (2003). “Post elastic behaviour of circular high-strength concrete columns confined with spirals.” CRGP Rep. No. 2001-02, Dept. of Civil Engineering, Univ. of Sherbrooke, Sherbrooke, Canada.
Saatcioglu, M., and Baingo, D. (1999). “Circular high-strength concrete columns under simulated seismic loading.” J. Struct. Eng., 125(3), 272–280.
Sheikh, S. A., and Khoury, S. S. (1993). “Confined concrete columns with stubs.” ACI Struct. J., 90(4), 414–431.
Sheikh, S. A., Shah, D. V., and Khoury, S. S. (1994). “Confinement of high-strength concrete columns.” ACI Struct. J., 91(1), 100–111.
Sheikh, S. A., and Uzumeri, S. M. (1982). “Analytical model for concrete confinement in tied columns.” J. Struct. Div., ASCE, 108(12), 2703–2722.
Standards New Zealand (NZS). (1995). “Code of practice for design of concrete structures.” NZS 3101, New Zealand.
Watson, S., and Park, R. (1994). “Simulated seismic load tests on reinforced concrete columns.” J. Struct. Eng., 120(6), 1825–1849.
Information & Authors
Information
Published In
Copyright
© 2008 ASCE.
History
Received: Sep 19, 2006
Accepted: Jul 13, 2007
Published online: May 1, 2008
Published in print: May 2008
Notes
Note. Associate Editor: Rob Y. H. Chai
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.