Pushover Response of a Braced Frame with Suspended Zipper Struts
Publication: Journal of Structural Engineering
Volume 134, Issue 10
Abstract
This paper presents the results from an experimental pushover test on a one-third-scale model of a special inverted-V-braced steel frame with zipper struts. Zipper elements are vertical elements added at the intersections of the braces above the first floor and designed to carry upward the unbalanced loads resulting from buckling of the braces. As far as the writers know, this is the first test on such a configuration that has been suggested as an alternate to conventional braced frames in the American Institute of Steel Construction seismic specification for many years. The model was pushed to a target roof drift ratio of , which was achieved without strength degradation and followed a trilinear backbone curve. The load was then reversed until the bottom story brace in tension fractured at a drift of . After this fracture, the frame still carried about 37% of the maximum base shear. The zipper elements demonstrated their ability to activate buckling in all stories except the top one, redistributing the loads in the structure and minimizing strength losses. Two-dimensional and one three-dimensional frame models were analyzed and found to reproduce satisfactorily the experimental results up to the beginning of tearing in the tension brace.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work is being carried out under NSF Grant No. 0324542 to Georgia Tech. The opinions given and results described herein are the exclusive responsibility of the senior writer and do not reflect the views of any of the universities involved, nor the National Science Foundation. This project is part of a pre-NEESR collaborative project with the University at Buffalo (Dr. A. Reinhorn and M. Schacter), the University of California at Berkeley (Dr. Stojadvonivic and T. Yang), the University of Colorado at Boulder (Dr. B. Shing and A. Stavridis), and Florida A&M (Dr. A. Makollah).
References
American Institute of Steel Construction (AISC). (2001a). Seismic provisions for structural steel buildings, AISC, Chicago.
American Institute of Steel Construction (AISC). (2001b). Manual of steel construction, load, and resistance factor design, AISC, Chicago.
American Institute of Steel Construction (AISC). (2005). Seismic provisions for structural steel buildings, AISC, Chicago.
Astaneh-Asl, A., Goel, S. C., and Hanson, R. D. (1986). “Earthquake-resistant design of double angle bracing.” Eng. J., 23(4).
Chopra, A. K., and Goel, R. K. (1998). “A modal pushover analysis procedure for estimating seismic demands for buildings.” Earthquake Eng. Struct. Dyn., 31(3), 561–582.
Federal Emergency Management Agency (FEMA). (2000). “State-of-the-art report on systems performance of steel moment frames subjected to earthquake ground shaking.” FEMA 355C, Building Seismic Safety Council, FEMA, Washington, D.C.
Hassan, O., and Goel, S. C. (1991). “Seismic behavior and design of concentrically braced steel structures.” Rep. UMCE 91-1, Dept. of Civil and Environmental Engineering, Univ. of Michigan, Ann Arbor, Mich.
International Code Council (ICC). (2000). International building code, ICC, Birmingham, Ala.
Khatib, I. F., Mahin, S. A., and Pister, K. S. (1988). “Seismic behavior of concentrically braced steel frames.” Rep. No. UCB/EERC-88/01, Earthquake Engineering Research Center, Univ. of California at Berkeley, Berkeley, Calif.
Kunnath, S. K., and Malley, J. O. (2002). “Advances in seismic design and evaluation of steel moment frames: Recent findings from FEMA/SAC phase II project.” J. Struct. Eng., 128(4), 415–419.
Leon, R. T., and Yang, C. S. (2003). “Special inverted-V-braced frames with suspended zipper struts.” Proc., Int. Workshop on Steel and Concrete Composite Construction, National Center for Research on Earthquake Engineering, Taipei, Taiwan, ⟨http://www.ncree.org.tw/iwsccc/PDF/09%20-%20Leon.pdf⟩ (July 4, 2005).
Schachter, R., and Reinhorn, L. (2006). “On the importance of 3D analysis for zipper frames structures.” Proc., 8th National Conf. of Earthquake Engineering, San Francisco.
Somerville, P. G., Smith, N., Punyamurthula, S., and Sun, J. (1997). “Development of ground motion time histories for Phase 2 of the FEMA/SAC steel project.” SAC Background Document Rep. No. SAC/BD 97/04.
Structural Engineers Association of Northern California (SEAONC). (2007). “Steel concentrically braced frames: Preliminary recommendations.” SEAONC Newsletter, LXII(3), 3.
Tang, X., and Goel, S. C. (1987). “Seismic analysis and design considerations of braced steel structures.” Rep. UMCE 87-4, Dept. of Civil and Environmental Engineering, Univ. of Michigan, Ann Arbor, Mich.
Tang, X., and Goel, S. C. (1989). “Brace fractures and analysis of phase I structure.” J. Struct. Eng., 115(8), 1960–1976.
Tremblay, R., and Tirca, L. (2003). “Behavior and design of multistory zipper concentrically braced steel frames for the mitigation of soft-story response.” Proc., 4th Int. Conf. on Behavior of Steel Structures in Seismic Areas (STESSA), Naples, Italy, 471–477.
Uriz, P., and Mahin, S. (2004). “Summary of test results for UC Berkeley special concentric braced frame specimen No. 1 (SCBF-1).” ⟨http://www.ce.berkeley.edu/~patxi/SCBF/publications/PelimSCBFtestResults.pdf⟩ (July 4, 2005).
Yang, C. S., Leon, R. T., and DesRoches, R. (2006a). “On the development of zipper frames by quasistatic testing and pushover analyses.” Proc., 8th National Conf. of Earthquake Engineering, San Francisco.
Yang, C. S., Leon, R. T., and DesRoches, R. (2006b). “On the development of zipper frames by pushover testing.” Proc., 5th Int. Conf. on Behavior of Steel Structures in Seismic Areas (STESSA), Yokohama, Japan, 555–561.
Yang, C. S., Leon, R. T., and DesRoches, R. (2008a). “Design and behavior of zipper-braced frames.” Eng. Struct., 30(4), 1092–1100.
Yang, C. S., Leon, R. T., and DesRoches, R. (2008b). “Cyclic behavior of zipper-braced frames.” Earthquake Spectra (in review).
Yang, T. Y., Stojadinovic, B., and Moehle, J. (2006c). “Hybrid simulation evaluation of innovative steel braced frame system.” Proc., 8th National Conf. of Earthquake Engineering, San Francisco.
Information & Authors
Information
Published In
Copyright
© 2008 ASCE.
History
Received: Sep 27, 2006
Accepted: Mar 21, 2008
Published online: Oct 1, 2008
Published in print: Oct 2008
Notes
Note. Associate Editor: James S. Davidson
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.