Efficient Energy Dissipating Steel-Braced Frame to Resist Seismic Loads
Publication: Journal of Structural Engineering
Volume 133, Issue 7
Abstract
In this research, the seismic performance of a proposed efficient energy dissipating steel-braced frame (EEDBF) in relation to that of a moment-resisting frame (MRF) and chevron braced frame (CBF) is studied. The frame is intended to combine the advantages of MRF and CBF and eliminate most of the disadvantages pertinent to these frames. Nonlinear static pushover, time history, and damage analyses of the three frames are conducted to assess the performance of the EEDBF compared to that of MRF and CBF. The analyses results revealed that the EEDBF has a more stable lateral force-deformation behavior compared to CBF. The energy dissipation capacity of the EEDBF is comparable to that of the MRF. The drift of the EEDBF at small to medium intensity ground motions is comparable to that of the CBF and smaller than that of the MRF. At high intensity ground motions, the drift of the EEDBF is smaller than those of both CBF and MRF. Furthermore, the EEDBF is found to experience less damage compared to other frames.
Get full access to this article
View all available purchase options and get full access to this article.
References
ADINA. (2004). Automatic dynamic incremental nonlinear analysis, version 8.2, ADINA R&D, Inc., Watertown, Mass.
AISC. (2001). Manual of steel construction, load, and resistance factor design, American Institute of Steel Construction, Chicago.
AISC. (2002) “Seismic provisions for structural steel buildings.” ANSI/AISC 341-02, American Institute of Steel Construction, Chicago.
Banon, H., Irvine, H. M., and Biggs, J. M. (1981). “Seismic damage in reinforced concrete frames,” J. Struct. Div., 107(9), 1713–1729.
Black, G. R., Wenger, B. A., and Popov, E. P. (1980). “Inelastic buckling of steel struts under cyclic load reversals,” Rep. No. UCB/EERC-80/40, Earthquake Engineering Research Center, Univ. of California, Berkeley, Calif.
Bruneau, M., Uang, C. M., and Whittaker, A. (1998). Ductile design of steel structures, McGraw-Hill, New York.
Chai, Y. H. (1999). “Characterization of story-level seismic damage using an energy-based damage model.” Exp. Mech., 39(1), 53–61.
Chen, C.-C., Chen, S.-Y., and Liaw, J.-J. (2001). “Application of low yield strength steel on controlled plastification ductile concentrically braced frames.” Can. J. Civ. Eng., 28(5), 823–836.
Clark, P., Aiken, I., Kasai, K., Ko, K., and Kimura, I. (1999). “Design procedures for building incorporating hysteretic damping devices.” Proc., 68th Annual Convention of the Structure Engineers Associate of California, Santa Barbara, Calif.
Della Corte, G., De Matteis, G., Landolfo, R., and Mazzolani, F. M. (2002). “Seismic analysis of MR steel frames based on refined hysteretic models of connections.” J. Constr. Steel Res., 58(10), 1331–1345.
Dicleli, M., and Albhaisi, S. M. (2004). “Effect of cyclic thermal loading on the performance of steel H piles in integral bridges with stub-abutments.” J. Constr. Steel Res., 60(2), 161–182.
Dicleli, M., and Buddaram, S. (2006). “Effect of isolator and ground motion characteristics on the performance of seismic-isolated bridges.” Earthquake Eng. Struct. Dyn., 35(2), 233–250.
Dicleli, M., and Mehta, A. (2007). “Simulation of inelastic cyclic buckling behavior of steel box sections.” Comput. Struct., 85(7–8), 446–457.
FEMA. (2000a). “NEHRP recommended provisions for the development of seismic regulations for new buildings and other structures.” BSSC 2000, Washington, D.C.
FEMA. (2000b), “Prestandard and commentary for the seismic rehabilitation of buildings.” FEMA 356, Washington D.C.
Georgescu, D., Toma, C., and Gosa, O. (1992). “Postcritical behavior of ‘K’ braced frames.” J. Constr. Steel Res., 21(1), 115–133.
Gwozdz, M., and Machowski, A. (1997). “Strengthening of building steel frames by modification of structural system.” Arch. Civ. Eng., 43(1), 37–49.
Hjelmstad, K. D., and Popov, E. P. (1983). “Cyclic behavior and design of link beams.” J. Struct. Eng., 109(10), 2387–2403.
Hindi, R. A., and Sexsmith, R. G. (2001). “A proposed damage for RC bridge columns under cyclic loading.” Earthquake Spectra, 17(2), 261–289.
Kasai, K., and Popov, E. P. (1986a). “General behavior of WF steel shear link beams.” J. Struct. Eng., 112(2), 362–382.
Kasai, K., and Popov, E. P. (1986b). “Cyclic web buckling control for shear link beams.” J. Struct. Eng., 112(3), 505–523.
Khashaee, P. (2005). “Damage-based seismic design of structures.” Earthquake Spectra, 21(2), 371–387.
Khatib, I. F., Mahin, S. A., and Pister, K. S. (1988). “Seismic behavior of concentrically braced steel frames.” Rep. No. UCB/EERC-88/01, Earthquake Engineering Research Center.
Kunnath, S. K., EL-Bahy, A., Taylor, A., and Stone, W. (1997). “Cumulative seismic damage of reinforced concrete bridge piers.” NCEER Rep. No. 97-0006, State Univ. of New York, Buffalo, N.Y.
McDaniel, C. C., Uang, C.-M. U., and Seible, F. (2003). “Cyclic testing of built-up steel shear inks for the New Bay Bridge.” J. Struct. Eng., 129(6), 801–809.
Mehanny, S. S. F., and Deierlein, G. G. (2001). “Seismic damage and collapse assessment of composite moment frames.” J. Struct. Eng., 127(9), 1045–1053.
Okazaki, T., Arce, G., Ryu, H.-C., and Engelhardt, M. D. (2005). “Experimental study of local buckling, overstrength, and fracture of links in eccentrically braced frames.” J. Struct. Eng., 131(10), 1526–1535.
Park, C. H., Lee, D. G., and Kim, J. K. (1997). “Effect of gravity load on seismic response of steel-framed structures.” Eng. Struct., 19(6), 439–451.
Park, Y. J., and Ang, A. H.-S. (1985). “Mechanistic seismic damage model for reinforced concrete.” J. Struct. Eng., 111(4), 722–739.
Perera, R., Carnicero, A., Alarcon, E., and Gomez, S. (2000). “Fatigue damage model for seismic response of RC structures.” Comput. Struct., 78(1), 293–302.
Perotti, F., and Scarlassara, G. P. (1991). “Concentrically braced frames under seismic actions: Nonlinear behavior and design coefficients.” Earthquake Eng. Struct. Dyn., 20(5), 409–427.
Phocas, M. C., and Pocanschi, A. (2003). “Steel frames with bracing mechanism and hysteretic dampers.” Earthquake Eng. Struct. Dyn., 32(5), 811–825.
Rai, D. C., Goel, S. C. (2003). “Seismic evaluation and upgrading of chevron braced frames.” J. Constr. Steel Res., 59(8), 971–994.
Redwood, R. G., and Channagiri, V. S., (1991). “Earthquake resistant design of concentrically braced steel frames.” Can. J. Civ. Eng., 18(5), 839–850.
Roeder, C. W. (1989). “Seismic behavior of concentrically braced frame.” J. Struct. Eng., 115(8), 1837–1855.
Sam, M.-T., Balendra, T., and Liaw, C.-Y. (1995). “Earthquake-resistant steel frames with energy dissipating knee elements.” Eng. Struct., 17(5), 334–343.
Tremblay, R., and Robert, N. (2001). “Seismic performance of low- and medium-rise chevron braced steel frames.” Basin Res., 28(4), 699–714.
Information & Authors
Information
Published In
Copyright
© 2007 ASCE.
History
Received: Mar 6, 2006
Accepted: Dec 14, 2006
Published online: Jul 1, 2007
Published in print: Jul 2007
Notes
Note. Associate Editor: Scott A. Civjan
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.