Web Yielding, Crippling, and Lateral Buckling under Post Loading
Publication: Journal of Structural Engineering
Volume 133, Issue 5
Abstract
Unstiffened, unbraced steel beams used in bridge falsework are subjected to patch loads from timber or steel posts. This paper investigates the critical web limit states in these types of beams experimentally and through finite-element analysis. Existing equations were appropriate for calculating the web yielding and crippling capacity, as observed in experiments, except that a 1:1 stress gradient through the flange and fillet of the web is found to be more appropriate and conservative for web yielding than the 2.5:1 gradient assumed in the current AISC specifications. Lateral deformation of a beam flange, due to buckling of the web, was also observed experimentally. The capacity of the web for resisting lateral buckling can be calculated assuming that the web of the beam acts like a column with an appropriate effective area and length factor. The effect of accidental eccentricity between the flange and post is not significant if limited to three times the web thickness. Blocking is approximately 50% effective in increasing the web yielding and crippling capacity. Bracing or stiffeners should be used to prevent lateral buckling of a web where necessary.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers would like to extend their gratitude to the California Department for Transportation for funding of this study under Contract No. UNSPECIFIED59A0445, with special thanks to John Lammers and Peter Lee for their assistance and direction.
References
AISC. (2005). Specification for structural steel buildings, Chicago.
American Forest and Paper Association (AFPA). (1996). Load and resistance factor design—Manual for engineered wood construction, Washington, D.C.
American Forest and Paper Association (AFPA). (2001). National design specification for wood construction, Washington, D.C.
California Department of Transportation (Caltrans). (2001). Falsework manual (updated November 2001), Caltrans Structure Construction, Sacramento, Calif.
Carden, L. P., Pekcan, G., and Itani, A. M. (2005). “Recommendations for the design of beams and posts in bridge falsework.” Center for Civil Engineering Earthquake Research Rep. No. CCEER 05–15, Univ. of Nevada–Reno, Reno, Nev.
Elgaaly, M. (1983). “Web design under compressive edge loads.” Eng. J., 20(4),153–171.
Elgaaly, M., and Nunan, W. L. (1989). “Behavior of rolled section web under eccentric edge compressive loads.” J. Struct. Eng., 115(7), 1561–1578.
Galambos, T. V. (1976). “Proposed criteria for load and resistance factor design of steel building structures.” Research Rep. No. 45, Civil Engineering Dept., Washington Univ., St Louis.
Graciano, C., and Edlund, B. (2003). “Failure mechanism of slender girder webs with a longitudinal stiffener under patch loading.” J. Constr. Steel Res., 59, 27–45.
Hibbett, Karlson and Sorensen, Inc. (2003). “ABAQUS—Finite-element program.” Users’ manual, Fremont, Calif.
Lucic, D. (2003). “Experimental research on I-girders subjected to eccentric patch loading.” J. Constr. Steel Res., 59, 1147–1157.
Roberts, T. M., and Markovic, N. (1983), “Stocky plate girders subjected to edge loading.” Proc. Inst. Civ. Eng., Part 2. Res. Theory, 75(2), 539–550.
Roberts, T. M., and Newark, A. C. B. (1997). “Strength of webs subjected to compressive edge loading.” J. Struct. Eng., 123(2), 176–183.
Roberts, T. M., and Rockey, K. C (1979). “A mechanism solution for predicting the collapse loads for slender plate girders when subjected to in-plane patch loading.” Proc. Inst. Civ. Eng., Part 2. Res. Theory, 67(2), 155–175.
Information & Authors
Information
Published In
Copyright
© 2007 ASCE.
History
Received: Oct 18, 2005
Accepted: Jul 27, 2006
Published online: May 1, 2007
Published in print: May 2007
Notes
Note. Associate Editor: Donald W. White
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.