Framed Steel Plate Wall Behavior under Cyclic Lateral Loading
This article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYPublication: Journal of Structural Engineering
Volume 133, Issue 3
Abstract
An experimental study was performed to investigate the cyclic behavior of framed steel walls with thin infill plates. Five specimens with a single bay and three stories were tested. Test parameters for the specimens were the plate thickness and the strength and compactness of the column. The test results showed that unlike conventional reinforced concrete walls and braced frames, well-designed steel plate walls exhibited large ductility and energy dissipation capacity as well as high strength. The steel plate walls with relatively thin plates showed shear-dominated behavior by the moment–frame action. On the other hand, steel plate walls with thick plates showed flexure-dominated behavior by the cantilever action. The shear-dominated walls showed better ductility. To achieve large ductility, the boundary columns must resist the combined axial force and transverse force developed by the tension–field action of the infill plates. Also, the columns must have compact sections to prevent their early local buckling.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgements
This research was financially supported by the Research Institute of Industrial Science and Technology (RIST) and the Ministry of Construction and Transportation of Korea (03 R&D C04-01, 05 R&D D06-01), and the writers are grateful to the authorities for their support.
References
American Institute of Steel Construction (AISC). (1999). Load and resistance factor design specification, Chicago.
American Institute of Steel Construction (AISC). (2002). Seismic provisions for structural steel buildings, Chicago.
Astaneh-Asl, A. (2001). “Seismic behavior and design of steel shear walls.” Steel TIPS Rep., Structural Steel Education Council, Moraga, Calif.
Behbahanifard, M. R. (2003). “Cyclic behavior of unstiffened steel plate shear walls.” Ph.D. dissertation, Dept. of Civil Engineering, Univ. of Alberta, Edmonton, Alberta, Canada.
Berman, J., and Bruneau, M. (2003). “Plastic analysis and design of steel plate shear walls.” J. Struct. Eng., 129(11), 1448–1456.
Caccese, V., Elgaaly, M., and Chen, R. (1993). “Experimental study of thin steel-plate shear walls under cyclic load.” J. Struct. Eng., 119(2), 573–587.
Canadian Standards Association (CSA). (2001). “Limit states design of steel structures.” CAN/CSA S16-01, Willowdale, Ontario.
Driver, R. G., Grondin, G. Y., Behbahanifard, M., and Hussain, M. A. (2001). “Recent developments and future directions in steel plate shear wall research.” Proc., North American Steel Construction Conf., AISC, Ft. Lauderdale, Fla.
Driver, R. G., Kulak, G. L., Kennedy, D. J. L., and Elwi, A. E. (1997). “Seismic behavior of steel plate shear walls.” Structural Engineering Rep. No. 215, Dept. of Civil Engineering, Univ. of Alberta, Edmonton, Alberta, Canada.
Driver, R. G., Kulak, G. L., Kennedy, D. J. L., and Elwi, A. E. (1998). “Cyclic test of a four-story steel plate shear wall.” J. Struct. Eng., 124(2), 112–130.
Elgaaly, M. (1998). “Thin steel plate shear walls behavior and analysis.” Thin-Walled Struct., 32, 151–180.
Hibbitt, Karlsson, and Sorenson, Inc. (HKS). (2003). ABAQUS standard, Version 6.4, HKS, Pawtucket, R.I.
Kulak, G. L., Kennedy, D. J. L., Driver, R. G., and Medhekar, M. (2001). “Steel plate shear walls—An overview.” Eng. J., 38(1), 50–62.
Lubell, A. S., Prion, H. G. L., Ventura, C. E., and Rezai, M. (2000). “Unstiffened steel plate shear wall performance under cyclic loading.” J. Struct. Eng., 126(4), 453–460.
Rezai, M. (1999). “Seismic behavior of steel plate shear wall by shake table testing.” Ph.D. dissertation, Univ. of British Columbia, Vancouver, British Columbia, Canada.
Thorburn, L. J., Kulak, G. L., and Montgomery, C. J. (1983). “Analysis of steel plate shear walls.” Structural Engineering Rep. No. 107, Dept. of Civil Engineering, Univ. of Alberta, Edmonton, Alberta, Canada.
Timler, P. A., and Kulak, G. L. (1983). “Experimental study of steel plate shear walls.” Structural Engineering Rep. No. 114, Dept. of Civil Engineering, Univ. of Alberta, Edmonton, Alberta, Canada.
Tromposch, E. W., and Kulak, G. L. (1987). “Cyclic and static behavior of thin panel steel plate shear walls.” Structural Engineering Rep. No. 145, Dept. of Civil Engineering, Univ. of Alberta, Edmonton, Alberta, Canada.
Xue, M., and Lu, L. W. (1994). “Interaction of infilled steel shear wall panels with surrounding frame members.” Proc., Structural Stability Research Council Annual Technical Session, SSRC, Bethlehem, Pa., 339–354.
Information & Authors
Information
Published In
Copyright
© 2007 ASCE.
History
Received: Jul 5, 2005
Accepted: Jul 27, 2006
Published online: Mar 1, 2007
Published in print: Mar 2007
Notes
Note. Associate Editor: Donald W. White
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.