Reliability of Steel Frames Designed with Advanced Analysis
Publication: Journal of Structural Engineering
Volume 132, Issue 2
Abstract
The design of steel frames by advanced analysis can result in more efficient structures while maintaining satisfactory levels of reliability by incorporating nonlinear structural analysis. The structural reliabilities of a series of two-story, two-bay steel frames designed by both load and resistance factor design (LRFD) and advanced analysis methods are compared. Yield strength and gravity loads are modeled as random variables. Strength distributions and probabilities of failure are calculated by Monte Carlo simulation and first-order approximation for two failure criteria—plastic collapse and first plastic hinge. The results indicate that LRFD methods successfully enforce the target reliability on first plastic hinging. In contrast, design by advanced analysis results in acceptable reliabilities against plastic collapse, but relatively large probabilities of plastic hinging at service load levels. Specifications based on advanced analysis may require greater attention to serviceability criteria. Resistance factors for advanced analysis are calculated based on the strength distributions for two levels of target reliability. System-based failure criteria, such as plastic frame collapse, present a fundamental difficulty in determining resistance factors applicable to a wide-range of structures.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research has been supported in part by a National Science Foundation Graduate Research Fellowship and Grant No. NSFDMI-0087032. The writers gratefully acknowledge the comments of Takeru Igusa of Johns Hopkins University.
References
American Institute of Steel Construction (AISC). (1999). Load and resistance factor design specification for structural steel buildings, 2nd Ed., Chicago.
Bartlett, F. M., Dexter, R. J., Graeser, M. D., Jelinek, J. J., Schmidt, B. J., and Galambos, T. V. (2003). “Updating standard shape material properties database for design and reliability.” Eng. J. AISC, 40(1), 2–14.
Bjorhovde R., Galambos, T. V., and Ravindra, M. K. (1978). “LRFD criteria for steel beam-columns.” J. Struct. Div. ASCE, 104(9), 1371–1387.
Buonopane, S. G. (2003). “Reliability and Bayesian approaches to the probabilistic performance based design of structures.” PhD dissertation, The Johns Hopkins Univ., Baltimore.
Chen, W. F., and Kim, S.-E. (1997). LRFD steel design using advanced analysis, CRC, Boca Raton, Fla.
Ellingwood, B., Galambos, T. V., MacGregor, J. G., and Cornell, C. A. (1980). “Development of a probability based load criterion for American national standard A58.” National Bureau of Standards Special Publication No. 577, NBS, U.S. Dept. of Commerce, Washington, D.C.
Federal Emergency Management Agency (FEMA). (2000). “State of the art report on base metals and fracture.” Rep. No. FEMA-355A., Washington, D.C.
Galambos, T. V. (1998). Guide to stability design criteria for metal structures, 5th Ed., Wiley, New York.
Galambos, T. V., and Ravindra, M. K. (1978). “Properties of steel for use in LRFD.” J. Struct. Div. ASCE, 104(9), 1459–1468.
Maleck, A. E., and White, D. W. (2003). “Direct analysis approach for the assessment of frame stability: Verification studies.” Proc., Annual Technical Session of the Structural Stability Research Council, Baltimore, 423–441.
McKenna, F., and Fenves, G. L. (2001). The OpenSees command language manual, Version 1.2, Pacific Earthquake Engineering Research Center, Univ. of California at Berkeley, Berkeley, Calif., ⟨http://opensees.berkeley. edu⟩.
Melchers, R. E. (1999). Structural reliability, 2nd Ed., Wiley, Chichester, U.K.
Nowak, A. S., and Szerszen, M. M. (2003). “Calibration of design code for buildings (ACI 318): Part 2—Reliability analysis and resistance factors.” ACI Struct. J., 100(3), 383–391.
Ravindra, M. K., and Galambos, T. V. (1978). “Load and resistance factor design for steel.” J. Struct. Div. ASCE, 104(9), 1337–1353.
Ziemian, R. D. (1990). “Advanced methods of inelastic analysis in the limit states design of steel structures.” PhD dissertation, Cornell Univ., Ithaca, N.Y.
Ziemian, R. D., McGuire, W., and Deierlein, G. G. (1992a). “Inelastic limit states design. Part I: Planar frame studies.” J. Struct. Eng., 118(9), 2532–2549.
Ziemian, R. D., McGuire, W., and Deierlein, G. G. (1992b). “Inelastic limit states design. Part II: Three-dimensional frame study.” J. Struct. Eng., 118(9), 2550–2568.
Information & Authors
Information
Published In
Copyright
© 2005 ASCE.
History
Received: Jun 11, 2004
Accepted: May 26, 2005
Published online: Feb 1, 2006
Published in print: Feb 2006
Notes
Note. Associate Editor: Donald W. White
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.