Shock Load Capacity of Concrete Expansion Anchoring Systems in Uncracked Concrete
This article is a reply.
VIEW THE ORIGINAL ARTICLEThis article has a reply.
VIEW THE REPLYPublication: Journal of Structural Engineering
Volume 131, Issue 8
Abstract
Concrete anchoring systems are commonly used in blast resistant wall systems. These anchoring systems are often subjected to large tensile forces in a short time during an external blast event. Previous research has been conducted on anchoring systems to evaluate their response to cyclic and “shock” loads; however, the ultimate capacities of these systems were not determined, and tests were conducted at relatively slow loading rates. In this paper, testing has been performed to determine the ultimate capacity of various expansion anchors at high loading rates, which is characteristic of most blast events. Ultimately, concrete expansion anchors perform differently at high loading rates and some show improved ultimate performance. This paper will present the experimental findings and provide recommendations for anchor design under blast loads.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers would like to acknowledge the research sponsorship of the U.S. Department of State (Mr. Wayne Ashbery, Mr. Donald Moffett) and the collaboration of the U.S. Army Corps of Engineers, Engineer Research and Development Center (Dr. Stanley Woodson and Dr. Beverly DiPaolo). Finally, the writers thank the Chief of Engineers for permission to publish this paper.
References
American Concrete Institute (ACI). (2002). “Building code requirements for structural concrete (ACI 318-02) and commentary (ACI 318R-02).” Farmington Hills, Mich.
Collins, D. M., Klingner, R. E., and Polyzois, D. (1989). “Load-deflection behavior of cast-in-place and retrofit concrete anchors subjected to static, fatigue, and impact tensile loads.” Research Rep. No. 1126-1, Center for Transportation Research
Dinan, R, Salim, H., Ashbery, W., Lane, J. and Townsend, P. T. (2003). “Recent experience using steel studs to construct blast resistant walls in reinforced concrete buildings.” Proc., 11th Int. Symp. on Interaction of the Effects of Munitions with Structures (11th ISIEMS), Streitkrafteamt, Germany and Defense Threat Reduction Agency.
DiPaolo, B., Salim, H., Townsend, T., and Davis, J. (2003). “A study on static and dynamic responses of exterior cold-formed steel-stud framing walls for enhanced blast resistance.” Proc. 16th Engineering Mechanics Conf., ASCE, Reston, Va.
Fuchs, W., Eligehausen, R., and Breen, J. E., (1995). Concrete capacity design approach for fastening to concrete.” ACI Struct. J., 92(1), 73–94.
Hilti (2002). Systems and solutions customer catalogue (brochure), Tulsa, Okla.
Hunziker, P. (1999). “Shock testing of concrete anchor bolts for shock resistant applications in protective structures.” Proc. 3rd Int. Conf. on Shock and Impact Loads on Structures,
Powers Faster Customer Catalogue. (2002) Concrete anchor product information and availability ⟨http://www.powers.com⟩
Rodriguez, M. et al. (2001). “Dynamic behavior of tensile anchors to concrete.” ACI Struct. J., 98(4), 511–524.
Salim, H., Dinan, R., Kiger, S., Townsend, P. T., and Shull, J. (2003). “Blast-retrofit wall systems using cold-formed steel studs.” Proc., 16th Engineering Mechanics Conf., ASCE, Reston, Va.
Shull, J. S. (2002) “Steel-stud retrofit connection development and design.” MS thesis, Univ. of Missouri, Columbia, Mo.
U.S. Nuclear Regulatory Commission. (NUREG). (1998). “Anchor bolt behavior and strength during earthquakes.” NUREG/CR-5434,
Young, W. C. (1989). Roark’s formulas for stress and strain, 6th Ed., McGraw-Hill, New York.
Information & Authors
Information
Published In
Copyright
© 2005 ASCE.
History
Received: Dec 23, 2003
Accepted: May 3, 2004
Published online: Aug 1, 2005
Published in print: Aug 2005
Notes
Note. Associate Editor: Barry Thomas Rosson
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.