Measuring Ground Anchor Forces of a Quay Wall with Bragg Sensors
Publication: Journal of Structural Engineering
Volume 131, Issue 2
Abstract
The use of optical fiber sensors for monitoring civil engineering structures is increasing continuously. One of the most frequently applied sensor types is the so-called Bragg sensor, which is primarily used to measure structural deformations. Due to some inherent advantages these sensors are ideally suited for long-term monitoring purposes. This paper describes the development of a load cell, based on Bragg sensors, to measure the forces in the ground anchors of a quay wall. After a short introduction on structural monitoring and the principles of a Bragg sensor, the concept of the load cell is discussed. Three ground anchors of a quay wall in Evergem, Belgium have been instrumented. After calibration in the laboratory, the load cells have been used to measure the prestressing forces imposed on the anchors. The results show that the developed instrumentation is very well suited for this purpose. For more than one year, the anchor forces have been monitored at regular points in time. This indicates a dependence of the anchor forces on environmental temperature variations.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers wish to thank the contractors Cinec and Herbosch-Kiere for the logistic help and financial support for this research project.
References
Brady, K., and Bush, D. (2001). “The performance of load cells used for ground anchorages.” Proc., 15th Int. Conf. on Soil Mechanics and Geotechnical Engineering, International Society for Soil Mechanics and Geotechnical Engineering, Istanbul, Turkey.
Brönnimann, R., Nellen, P. M., and Sennhauser, U. (1998). “Application and reliability of a fiber optical surveillance system for a stay cable bridge.” Smart Mater. Struct., 7, 229–236.
Dakin, J., and Culshaw, B. (1997). Optical fiber sensors: Applications, analysis, and future trends, Vol. 4, Artech House, Boston.
Degrieck, J., De Waele, W., and Verleysen, P. (2001). “In-service monitoring of fiber reinforced composites with Bragg sensors.” NDT & E Int., 34, 289–296.
Del Grosso, A., Inaudi, D., and Lanata, F. (2000). “Strain and displacement monitoring of a quay wall in the Port of Genoa by means of fibre optic sensors.” Proc., 2nd European Conf. on Structural Control, Laboratoire Central des Ponts et Chaussées, Champs-sur-Marne, France.
De Waele, W., Degrieck, J., Baets, R., Moerman, W., and Taerwe, L. (2001). “Load and deformation monitoring of composite pressure vessels by means of optical fiber sensors.” Insight, 43(8), 518–525.
De Waele, W., Degrieck, J., Moerman, W., Taerwe, L., and De Baets, P. (2003a). “Feasibility of integrated optical fiber sensors for condition monitoring of composite structures. I: Comparison of Bragg-sensors and strain gauges.” Insight, 45(4), 266–271.
De Waele, W., Degrieck, J., De Baets, P., Moerman, W., and Taerwe, L. (2003b). “Feasibility of integrated optical fiber sensors for condition monitoring of composite structures. II: Combination of Bragg-sensors and acoustic-emission detection.” Insight, 45(8), 542-546.
Dixon, R. W. (1967). “Photoelastic properties of selected materials and their relevance for applications to acoustic light modulators and scanners.” J. Appl. Phys., 38, 5149–5153.
ElectroPhotonics Solutions. (2000). “E-TEK, sensor specifications.” Technical information.
Fuhr, P., Huston, D., Kajenski, P., and Ambrose, T. (1992). “Performance and health monitoring of the Stafford Medical Building using embedded sensors.” Smart Mater. Struct., 1, 63–68.
Gattermann, J., Bergs, T., and Rodatz, W. (2001). “Modified instrumentation and results of stress and deformation monitoring at the new quay wall construction—Container Terminal Altenwerder, Port of Hamburg.” Proc., 8th Int. Conf. on Structural Safety and Reliability, Swets & Zeitlinger, Lisse, The Netherlands.
Geokon, Incorporated. (2002). “Geotechnical instrumentation—Load cells.” Technical brochure, DOC.REV.A 1/02-1-2M.
Hill, K. O., and Meltz, G. (1997). “Fiber Bragg grating technology fundamentals and overview.” J. Lightwave Technol., 15, 1263-1276.
Maaskant, R., et al. (1997). “Fiber-optic Bragg grating sensors for bridge monitoring.” Cem. Concr. Compos., 19(1), 21–33.
Measures, R. M. (2001). Structural monitoring with fiber optic technology, Academic, San Diego.
Meltz, G., Morey, W. W., and Glenn, W. H. (1989). “Formation of Bragg gratings in optical fibers by a transverse holographic method.” Opt. Lett., 14(15), 823–825.
Moerman, W., et al. (2001a). “Monitoring of a prestressed concrete girder bridge with fiber optical bragg grating sensors.” Strain J. Brit. Soc. Strain Measurement, 37(4), 151–153.
Moerman, W., Taerwe, L., De Waele, W., Degrieck, J., and Baets, R. (2001b). “Bragg grating strain measurements during the construction of a prestressed concrete girder bridge.” Insight, 43(7), 467–469.
Moerman, W., Taerwe, L., De Waele, W., Degrieck, J., and Baets, R. (2001c). “Application of optical fiber sensors for monitoring civil engineering structures.” Structural Concrete, 2(2), 63–71.
National Physics Laboratory. (2003). “Frequently asked questions—Force.” ⟨http://www.npl.co.uk/force/faqs/transcharacter.html⟩ (July 22, 2003).
Schwesinger, P., Bolle, G., and Berndt, R. D. (1998). “Remote monitoring for controlled life extension of concrete structures.” Proc., 5th Int. Workshop on Material Properties and Design, Bauhaus-University Weimar, 515–528 (Germany).
Udd, E. (1996). “Fiber optic smart structures.” Proc. IEEE, 84(1), 60–66.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 131 • Issue 2 • February 2005
Pages: 322 - 328
Copyright
© 2005 ASCE.
History
Received: Aug 21, 2001
Accepted: May 25, 2004
Published online: Feb 1, 2005
Published in print: Feb 2005
Notes
Note. Associate Editor: Donald O. Dusenberry
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.