Experimental Investigation of Light-Gauge Steel Plate Shear Walls
Publication: Journal of Structural Engineering
Volume 131, Issue 2
Abstract
This paper describes the prototype design, specimen design, experimental setup, and experimental results of three light-gauge steel plate shear wall concepts. Prototype light-gauge steel plate shear walls are designed as seismic retrofits for a hospital structure in an area of high seismicity, and emphasis is placed on minimizing their impact on the existing framing. Three single-story test specimens are designed using these prototypes as a basis, two specimens with flat infill plates (thicknesses of ) and a third using a corrugated infill plate (thickness of ). Connection of the infill plates to the boundary frames is achieved through the use of bolts in combination with industrial strength epoxy or welds, allowing for mobility of the infills if desired. Testing of the systems is done under quasi-static conditions. It is shown that one of the flat infill plate specimens, as well as the specimen utilizing a corrugated infill plate, achieve significant ductility and energy dissipation while minimizing the demands placed on the surrounding framing. Experimental results are compared to monotonic pushover predictions from computer analysis using a simple model and good agreement is observed.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgment
This work was supported in whole by the Earthquake Engineering Research Centers Program of the National Science Foundation under Award No. ECC-9701471 to the Multidisciplinary Center for Earthquake Engineering Research. However, any opinions, findings, conclusions, and recommendations presented in this paper are those of the writers and do not necessarily reflect the views of the sponsors.
References
Applied Technology Council. (ATC). (1992). “Guidelines for seismic testing of components of steel structures.” Rep. No. 24, ATC, Redwood City, CA 94065.
ASTM. (1997). “Standard specification for commercial steel sheet, carbon, cold-rolled.” A 366/A 336M-97, American Society for Testing and Materials, Philadelphia.
ASTM. (1998). “Standard specification for steel sheet, zinc-coated (galvanized) zinc-iron alloy-coated (galvannealed) by the hot-dip process.” A 653/A 653M-98, American Society for Testing and Materials, Philadelphia.
Berman, J. W., and Bruneau, M. (2003a). “Experimental investigation of light-gauge steel plate shear walls for the seismic retrofit of buildings.” Tech. Rep. No. MCEER-03-0001, Multidisciplinary Center for Earthquake Engineering Research, Univ. at Buffalo, Buffalo, N.Y.
Berman, J. W., and Bruneau, M. (2003b). “Plastic analysis and design of steel plate shear walls.” J. Struct. Eng., 129(11), 1148–1156.
Bruneau, M., Uang, C. M., and Whittaker, A. (1997). Ductile design of steel structures, McGraw-Hill, N.Y.
Caccese, V., Elgaaly, M., and Chen, R. (1993). “Experimental study of thin steel-plate shear walls under cyclic load.” J. Struct. Eng., 119(2), 573–587.
Canadian Standards Association (CSA). (2001). “Limit states design of steel structures.” CAN/CSA S16-01, Willowdale, Ontario, Canada.
Chen, W. F., Goto, Y., and Liew, J. Y. R. (1996). Stability design of semirigid frames, Wiley, N.Y.
Cook, N. E. (1983). “Strength of flexibly-connected steel frames under load histories.” PhD dissertation, Univ. of Colorado—Boulder, Boulder, Colo.
Dafalias, Y. F., and Popov, E. P. (1976). “Plastic internal variables formalism of cyclic plasticity.” J. Appl. Mech., 43, 645–651.
Driver, R. G., Kulak, G. L., Kennedy, D. J. L., and Elwi, A. E. (1997). “Seismic behavior of steel plate shear walls.” Structural Engineering Rep. No. 215, Dept. of Civil Engineering, Univ. of Alberta, Edmonton, Alberta, Canada.
Elgaaly, M., Caccese, V., and Du, C. (1993). “Postbuckling behavior of steel-plate shear walls under cyclic loads.” J. Struct. Eng., 119(2), 588–605.
Federal Emergency Management Agency (FEMA). (1997). “NEHRP Recommended Provisions for Seismic Regulations for New Buildings and Other Structures, Part-1-Provisions.” FEMA 302, Building Seismic Safety Council for the FEMA, Washington, D.C.
Goto, Y., Suzuki, S., and Chen, W. F. (1991). “Analysis of critical behavior of semirigid frames with or without load histories in connections.” Int. J. Solids Struct., 27(4), 467–483.
Loctite. (2001). “Product description sheet-Hysol product 9460.” Loctite Inc., Rocky Hill, Conn.
MathWorks. (1999). MatLab Function Reference, The MathWorks, Inc., Natick, Mass.
Rezai, M. (1999). “Seismic behavior of steel plate shear walls by shake table testing.” PhD dissertation, Univ. of British Columbia, Vancouver, British Columbia, Canada.
Thorburn, L. J., Kulak, G. L., and Montgomery, C. J. (1983). “Analysis of steel plate shear walls.” Structural Engineering Rep. No. 107, Dept. of Civil Engineering, Univ. of Alberta, Edmonton, Alberta, Canada.
Timler, P. A., and Kulak, G. L. (1983). “Experimental study of steel plate shear walls.” Structural Engineering Report No. 114, Dept. of Civil Engineering, Univ. of Alberta, Edmonton, Alberta, Canada.
Yang, T. Y., and Whittaker, A. (2002). “MCEER demonstration hospitals-Mathematical models and preliminary results.” Tech. Rep., Multidisciplinary Center for Earthquake Engineering Research, Univ. at Buffalo, Buffalo, N.Y.
Information & Authors
Information
Published In
Copyright
© 2005 ASCE.
History
Received: Mar 25, 2003
Accepted: May 11, 2004
Published online: Feb 1, 2005
Published in print: Feb 2005
Notes
Note. Associate Editor: Christopher J. Earls
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.