Construction Considerations for Composite Steel-and-Concrete Floor Systems
Publication: Journal of Structural Engineering
Volume 128, Issue 9
Abstract
This report presents an overview of construction methods for the most commonly used composite steel-and-concrete floor system in U.S. buildings. The report was prepared by a subcommittee of the ASCE Committee on Composite Construction and is intended to assist practitioners by summarizing practical and effective means to avoid common construction problems. Four principal components of the floor system are considered: (1) steel section, (2) steel deck, (3) headed shear stud, and (4) concrete slab. Proper construction procedures for each component are discussed and summarized. Reasonable adherence to specifications and communication between designers and builders will minimize difficulties in the construction of composite steel-and-concrete floor systems.
Get full access to this article
View all available purchase options and get full access to this article.
References
Alsamsam, I. M. (1991). “Serviceability criteria for composite floor systems.” PhD thesis, Univ. of Minnesota, Minneapolis.
American Concrete Institute (ACI) (1996). Guide for concrete floor and slab construction (ACI 302.1 R-96), American Concrete Institute, Farmington Hills, Mich.
AISC. (1999). Load and resistance factor design manual of steel construction, Chicago.
AISC. (1997). “Control of floor elevation and levelness.” Seminar Notes, Chicago.
ASCE. (1991). “Standard for the structural design of composite slabs/standard practice for construction and inspection of composite slabs.” ANSI/ASCE 9-91, New York.
ASTM. (1987). “Standard test method for determining floor flatness and levelness using the F-number system.” E 1155-87, West Conshoholan, Pa.
American Welding Society, (AWS). (1998). “Structural welding code—Section 7: Stud welding.” ANSI/AWS D1.1-98, Miami.
Chien, E. Y. L., and Ritchie, J. K. (1984). Design and construction of composite floor systems, Canadian Institute of Steel Construction, Ontario, Canada.
“Composite framing stunts concrete market growth.” (1995). Concr. Constr., February, 221–222.
Cook, R. J. (1989). “Building concrete slabs composite with steel frames: Contractors should be alert to shoring problems.” Concr. Constr., November, 938–942.
Fling, R. S. (1990). “Someone has to pay when building components don’t fit—Even if tolerances are met.” Concr. Constr., January, 50–56.
Fricks, T. J. (1994). “Misunderstandings and abuses in flatwork specifications.” Concr. Constr., June, 492–497.
Griffis, L. G. (1994). “Composite frame construction.” Modern Steel Constr., October, 36–47.
Heagler, R. B. (1996). Metal deck and concrete quantities, Steel Deck Institute, Fox River Grove, Ill.
Heagler, R. B., Luttrell, L. D., and Easterling, W. S. (1997). Composite deck design handbook, Steel Deck Institute, Fox River Grove, Ill.
Kloiber, L. A. (1989). “Cambering of steel beams.” Proc. Steel Structures, ASCE, New York, 101–110.
Larson, J. W., and Huzzard R. K. (1990). “Economical use of cambered steel beams.” Proc. AISC Engineering Conference, Chicago, 3–21.
Leon, R. L., and Alsamsam, I. (1993). “Performance and serviceability of composite floors.” Structural Engineering in Natural Hazards Mitigation, ASCE, New York.
Malisch, W. R. (1991). “Sagging slabs: What are the options.” Concr. Constr., January, 7.
“Nelson stud welding for non-residential construction.” (1988). TRW Nelson Stud welding Division, Elyria, Ohio.
Rex, C. O., and Easterling, W. S. (1994). “Reducing serviceability concerns.” Modern Steel Constr., February, 22–26.
Ricker, Jr., D. T.(1989). “Cambering steel beams.” AISC Engineering Journal 4, 136–142.
Ruddy, J. L.(1986). “Ponding of concrete deck slabs.” AISC Engineering Journal 3, 107–115.
Ryan, J. T. (1997). “Controlling deflection of composite deck slabs.” Publication no. C970734, Aberdeen Group, Addison, Ill.
Steel Deck Institute (SDI). (1995). SDI manual of construction with steel deck, Fox River Grove, Ill.
Suprenant, B. A. (1991). “Construction of elevated slabs: Understanding the effect of structural systems.” Concr. Constr., November, 910–920.
Tipping, E. (1992). “Building superior quality elevated floors.” Publication no. C920285, Aberdeen Group, Addison, Ill.
Tipping, E., and Suprenant, B. A. (1991a). “Construction of elevated slabs: Practice and procedures.” Concr. Constr., January, 32–42.
Tipping, E., and Suprenant, B. A. (1991b). “Construction of elevated slabs: Measuring and evaluating quality.” Concr. Constr., March, 260–268.
Viest, I. M., Colaco, J. P., Furlong, R. W., Griffis, G. G., Leon, T. L. and Wyllie, L. A. (1997). Composite construction design for buildings, McGraw-Hill, New York.
Information & Authors
Information
Published In
Copyright
Copyright © 2002 American Society of Civil Engineers.
History
Received: May 28, 2002
Accepted: May 28, 2002
Published online: Aug 15, 2002
Published in print: Sep 2002
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.