Test Method for Determining the Shear Modulus of Elastomeric Bearings
Publication: Journal of Structural Engineering
Volume 128, Issue 6
Abstract
The shear modulus of the elastomer is the most important material property related to the behavior of elastomeric bearings used principally at supports in bridges. Current methods for determining the shear modulus usually require small test samples cut from manufactured bearings. Such tests are costly, do not necessarily represent the performance of the full-size bearing, and are destructive. A new shear test method, called the inclined compression test, is reported that is nondestructive and only requires a compression test machine to apply shear to the full-size bearing. The results from the inclined compression test show good correlation with results from an independent full-scale test setup. To develop reliable test procedures various test parameters were evaluated such as testing speed, platen surface conditions, and specimen dimensions. The test results show that the inclined compression method is a practical alternative to more traditional test methods. The new method works very well on bearings reinforced with steel laminates, but plain bearings require cold bonding to attachment plates in order to obtain reliable shear moduli.
Get full access to this article
View all available purchase options and get full access to this article.
References
AASHTO. (1996). Standard specification for highway bridges, 16th Ed.
AASHTO. (1997). Standard specification for plain and laminated elastomeric bridge bearings, M251-97, Washington, D.C.
ASTM. (1989). Standard specification for plain and laminated elastomeric bearings for bridges, D0414-89, West Conshohocken, Pa.
Arditzoglou, Y., Yura, J. A., and Haines, A. H. (1997), “An evaluation of the ASTM shear modulus test for elastomeric bridge bearings.” Fourth world congress on joint sealants and bearing systems in concrete structures, American Concrete Institute, SP-164V2, 2, 903–936, Sacramento, Calif.
Crozier, W. F., Stoker, J. R., Martin, V. C., and Nordlin, E. F. (1974). “A laboratory evaluation of full-size elastomeric bridge bearing pads.” Rep. No. CA-DOT-TL-6574-1-74-26, Transportation Laboratory, State of California, Division of Highways, 61 pp.
Eurocode (1996). “Structural Bearings: Part 3, Elastomeric Bearings.” Draft Document No. prEN 1337-3.
Hamzeh, O., Tassoulas, J. L., and Becker, E. B. (1995). “Analysis of elastomeric bridge bearings,” Rep. No. 1304-5, Center for Transportation Research, Univ. of Texas, Austin, August, 139 pp.
Kelly, J. M. (1997). Earthquake-resistant design with rubber, 2nd Ed., Springer, London.
Kumar, A. (2000). “Performance related parameters of elastomeric bearings.” PhD dissertation, Univ. of Texas at Austin.
Mullins, L.(1987). “Engineering with rubber.” CHEMTECH, 17(12), 720–727.
Muscarella, J. V., and Yura, J. A. (1995). “An experimental study of elastomeric bridge bearings with design recommendations.” Research Rep. No. 1304-3, Center for Transportation Research, Univ. of Texas, Austin, October, 180 pp.
Topkaya, C. (1999). “A new test method for determining the shear modulus of elastomeric bridge bearings.” Master’s thesis, Univ. of Texas at Austin, Austin, Tex.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 128 • Issue 6 • June 2002
Pages: 797 - 805
Copyright
Copyright © 2002 American Society of Civil Engineers.
History
Received: Sep 8, 2000
Accepted: Aug 2, 2001
Published online: May 15, 2002
Published in print: Jun 2002
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.