Cyclic Pull-Out Strength of Screwed Connections in Steel Roof and Wall Cladding Systems using Thin Steel Battens
Publication: Journal of Structural Engineering
Volume 128, Issue 6
Abstract
When crest-fixed thin steel roof and wall cladding systems are subjected to wind uplift or suction loading, local pull-through or pull-out failures occur prematurely at their screwed connections. During high wind events such as storms and hurricanes these localized failures then lead to severe damage to buildings and their contents. In recent times, the use of thin steel battens/purlins has increased considerably. This has made the pull-out failures more critical in the design of steel cladding systems. Recent research has developed a design formula for the static pull-out strength of screwed connections in steel cladding systems. However, the effects of fluctuating wind uplift or suction loading that occurs during high wind events are not known. Therefore, a series of cyclic wind uplift/suction tests has been undertaken on connections between thin steel battens made of different thicknesses and steel grades, and screw fasteners with varying diameter and pitch. Tests revealed a significant reduction to pull-out strength caused by fluctuating wind loading. Simple design equations and suitable recommendations were developed to take into account this strength reduction. This paper presents the details of the cyclic tests and the results.
Get full access to this article
View all available purchase options and get full access to this article.
References
American Iron and Steel Institute (AISI). (1996). Specification for the design of cold-formed steel structural members, Washington, D.C.
Baskaran, A., and Dutt, Om.(1997). “Performance of roof fasteners under simulated loading condition.” J. Wind Eng., 72(3), 389–400.
Beck, V. R., and Stevens, L. K.(1979). “Wind loading failures of corrugated roof cladding.” Civil Eng. Trans., IEAust., 21(1), 45–56.
Ellifritt, D. and Burnette, R. (1990). “Pull-over strength of screws in simulated building tests.” Proc., 10th Int. Speciality Conf. on Cold-formed Steel Structures, St. Louis, 589–603.
Eurocode 3. (1992). Design of steel structures, Part 1.3—Cold-formed thin-gauge members and sheeting, Commission of European Communities, Brussels, Belgium.
Macindoe, L., Adams, J., and Pham, L. (1995). “Performance of single point fasteners. Report to the CRC for materials, welding and joining.” CSIRO Division of Building, Construction and Engineering, Melbourne, Australia.
Mahendran, M.(1990a). “Fatigue behaviour of corrugated roofing under cyclic wind loading.” Civil Eng. Trans., IEAust, 32(4), 219–226.
Mahendran, M.(1990b). “Static behaviour of corrugated roofing under simulated wind loading.” Civil Eng. Trans., IE Aust., 32(4), 211–218.
Mahendran, M.(1994). “Behaviour and design of crest-fixed profiled steel roof claddings under high wind forces.” Eng. Struct., 16(5), 368–376.
Mahendran, M., and Tang, R. B. (1996). “Pull-out strength of steel roof and wall cladding systems,”Research Rep. 96-38, Physical Infrastructure Centre, Queensland Univ. of Technology, Brisbane, Australia.
Mahendran, M., and Tang, R. B. (1998). “Pull-out strength of steel roof and wall cladding systems.” ASCE J. Struct. Eng., 124(10), 1192–1201.
Mahendran, M., and Mahaarachchi, D. (2000). “Cyclic pull-out strength of steel roof and wall cladding systems,” Research Monograph 2000-10, Physical Infrastructure Centre, Queensland Univ. of Technology, Brisbane, Australia.
Pekoz, T. (1990). “Design of cold-formed steel screw connections.” Proc., 10th Int. Speciality Conf. on Cold-formed Steel Structures, St. Louis, 576–587.
Standards Australia (SA). (1989). “Loading code Part 2: wind loads.” AS 1170, Sydney, Australia.
Standards Australia (SA). (1996). “Cold-formed steel structures code.” AS 4600, Sydney, Australia.
Toma, A., Sedlacek, G., and Weynand, K.(1993). “Connections in cold-formed steel.” Thin-Walled Struct., 16, 219–237.
Xu, Y. L., and Reardon, G. F.(1993). “Test of screw fastened profiled roofing sheets subject to simulated wind uplift.” Eng. Struct., 15(6), 423–430.
Information & Authors
Information
Published In
Copyright
Copyright © 2002 American Society of Civil Engineers.
History
Received: Feb 8, 2001
Accepted: Oct 22, 2001
Published online: May 15, 2002
Published in print: Jun 2002
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.