Strength Design of Steel I-Section Beams Curved in Plan
Publication: Journal of Structural Engineering
Volume 127, Issue 6
Abstract
When a steel I-section beam that is curved in plan is subjected to vertical (or transverse) loading, its primary actions are bending about its major axis and torsion. Secondary torsion and minor axis bending actions are usually significant in steel I-section beams curved in plan under combined bending and torsion. However, the common circular interaction equation used in practice for rectangular solid or hollow section curved beams does not account for these significant effects and so may overestimate the interaction strength of steel I-section beams curved in plan under bending and torsion. This paper investigates the nonlinear elastic-plastic behavior of steel I-section beams curved in plan under vertical loading and proposes straightforward formulas for their design against combined bending and torsion actions. Comparisons with rational finite-element results and existing experimental results show that the proposed interaction equations provide a good lower bound for the design of steel I-section beams curved in plan against combined bending and torsion. The proposed interaction equations are simple and consistent with existing codified design rules.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
ABAQUS user's manual. Version 5.8. (1998). Hibbitt, Karlsson & Sorensen, Inc., Pawtucket, R.I.
2.
American Institute of Steel Construction (AISC). ( 1993). Load and resistance factor design specification for structural steel buildings, Chicago.
3.
Bradford, M. A., and Cuk, P. E. (1988). “Elastic buckling of tapered monosymmetric I-beams.”J. Struct. Engrg., ASCE, 114(5), 977–996.
4.
Bradford, M. A., and Trahair, N. S. ( 1985). “Inelastic buckling of beam-columns with unequal end moments.” J. Constr. Steel Res., 5(2), 195–212.
5.
Bradford, M. A., Uy, B., and Pi, Y.-L. ( 2001). “Behaviour of unpropped composite girders curved in plan under construction.” Engrg. Struct., in press.
6.
Boulton, N. S., and Boonsukha, B. ( 1959). “Plastic collapse loads for circular-arc bow girders.” Inst. of Civ. Engrs., 13(6), 161–178.
7.
Dinno, K. S., and Merchant, W. ( 1965). “A procedure for calculating the plastic collapse of I-sections under bending and torsion.” The Struct. Engr., London, 43(7), 219–221.
8.
Fukumoto, Y., and Nishida, S. (1981). “Ultimate load behavior of curved I-beams.”J. Engrg. Mech. Div., ASCE, 107(2), 367–385.
9.
Gendy, A. S., and Saleeb, A. F. ( 1992). “On the finite element analysis of the spatial response of curved beams with arbitrary thin-walled sections.” Comp. and Struct., 44(3), 639–652.
10.
Gill, S. S., and Boucher, J. K. G. ( 1964). “An experimental investigation of plastic collapse of structural members under combined bending and torsion.” The Struct. Engr., London, 42(12), 423–428.
11.
Hodge, P. G. ( 1959). Plastic analysis of structures, McGraw-Hill, London.
12.
Imegwu, E. O. ( 1960). “Plastic flexure and torsion.” J. Mech. Phys. Solids, 8, 141–146.
13.
Jackson, N. (1966). “Collapse loads for circular-arc beams.”J. Struct. Div., ASCE, 92(5), 1–14.
14.
Nakai, H., and Yoo, C. H. ( 1988). Analysis and design of curved steel bridges, McGraw-Hill, New York.
15.
Nethercot, D. A., Salter, P. R., and Malik, A. S. ( 1989). “Design of members subjected to combined bending and torsion.” SCI Publ. 057, Steel Construction Institute, Ascot, England.
16.
Pi, Y.-L., and Bradford, M. A. ( 2001a). “Effects of approximations in analyses of beams of open, thin-walled cross section: 1. flexural-torsional stability.” Int. J. Numer. Methods in Engrg., in press.
17.
Pi, Y.-L., and Bradford, M. A. ( 2001b). “Effects of approximations in analyses of beams of open, thin-walled cross-section: 2. 3-D nonlinear behaviour.” Int. J. Numer. Methods in Engrg., in press.
18.
Pi, Y.-L., Bradford, M. A., and Trahair, N. S. (2000). “Inelastic analysis and behavior of steel I-beams curved in plan.”J. Struct. Engrg., ASCE, 126(7), 772–779.
19.
Pi, Y.-L., and Trahair, N. S. (1994). “Inelastic bending and torsion of steel I-beams.”J. Struct. Engrg., ASCE, 120(12), 3397–3417.
20.
Pi, Y.-L., and Trahair, N. S. (1995). “Inelastic torsion of steel I-beams.”J. Struct. Engrg., ASCE, 121(4), 609–620.
21.
Pi, Y.-L., and Trahair, N. S. (1997). “Nonlinear elastic behavior of I-beams curved in plan.”J. Struct. Engrg., ASCE, 123(9), 1201–1209.
22.
Shanmugam, N. E., Thevendran, V., Liew, J. Y. R., and Tan, L. O. (1995). “Experimental study on steel beams curved in plan.”J. Struct. Engrg., ASCE, 121(2), 249–259.
23.
Standards Australia (SA). ( 1998). AS4100 Steel structures, Sydney, Australia.
24.
Timoshenko, S. P., and Gere, J. M. ( 1961). Theory of elastic stability, 2nd Ed., McGraw-Hill, New York.
25.
Trahair, N. S., and Bradford, M. A. ( 1991). The behaviour and design of steel structures, Revised 2nd Ed., Chapman & Hall, London.
26.
Trahair, N. S., and Bradford, M. A. ( 1998). The behaviour and design of steel structures to AS4100, 3rd Australian Ed., E & FN Spon, London.
27.
Vlasov, V. Z. ( 1961). Thin-walled elastic beams, 2nd Ed., Israel Program for Scientific Translation, Jerusalem.
28.
Woolcock, S. T., Kitipornchai, S., and Bradford, M. A. ( 1999). Design of portal frame buildings, 3rd Ed., Australian Institute of Steel Construction, Sydney, Australia.
29.
Yoo, C. H., and Heins, C. P. (1972). “Plastic collapse of horizontally curved bridge girders.”J. Struct. Div., ASCE, 98(4), 899–914.
30.
Yoshida, H., and Maegawa, K. (1983). “Ultimate strength analysis of curved I-beams.”J. Engrg. Mech., ASCE, 109(1).192–214
Information & Authors
Information
Published In
History
Received: Mar 16, 2000
Published online: Jun 1, 2001
Published in print: Jun 2001
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.