Energy Based Methodology for Ductile Design of Concrete Columns
Publication: Journal of Structural Engineering
Volume 127, Issue 12
Abstract
Potential plastic hinge zones in confined concrete columns require that sufficient transverse reinforcement be provided to avert undesirable failure modes and to ensure dependable inelastic (ductile) behavior in earthquakes. Conventional code-based approaches for detailing confining reinforcement are founded on the premise of preserving axial load before and after spalling of the cover concrete. Such formulations account for neither the cyclic actions nor the duration effects of ground motions. This paper derives the amount of transverse reinforcement necessary so that hoop fracture and fatigue fracture of the longitudinal bars coincide for critical earthquake motions. An energy-based approach coupled with notions of low cycle fatigue are used for this purpose.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
American Association of State Highway Transportation Officials (AASHTO). ( 1994). AASHTO LRFD bridge design specifications, 1st Ed., Washington, D.C.
2.
American Concrete Institute (ACI). ( 1995). “Building code requirements for reinforced concrete.” ACI-318-95, Detroit.
3.
Ang, B. G., Priestley, M. J. N., and Paulay, T. ( 1989). “Seismic shear strength of circular reinforced concrete columns.” ACI Struct. J., 86(1).
4.
Applied Technology Council (ATC). ( 1996). “Improved seismic design criteria for California bridges: Provisional recommendations.” ATC-32, Redwood City, Calif.
5.
Aycardi, L. E., Mander, J. B., and Reinhorn, A. M. ( 1994). “Seismic resistance of reinforced concrete frame structures designed only for gravity loads: Experimental performance of subassemblages.” ACI Struct. J., 91(5).
6.
Chai, Y. H., Priestley, M. J. N., and Seible, F. ( 1991). “A seismic retrofit of circular bridge columns for enhanced bridge performance.” ACI Struct. J., 88(5).
7.
Chang, G. A., and Mander, J. B. ( 1994). “Seismic energy based fatigue damage analysis of bridge columns. Part II: Evaluation of seismic demand.” Tech. Rep. NCEER-94-0013, Nat. Ctr. for Earthquake Engrg. Res., State University of New York at Buffalo, Buffalo, N.Y.
8.
Dutta, A. ( 1995). “Fatigue analysis of non-ductile concrete columns.” MS thesis, Dept. of Civ. Engrg., State University of New York at Buffalo, Buffalo, N.Y.
9.
Dutta, A., and Mander, J. B. ( 1998). “Capacity design and fatigue analysis of confined concrete columns.” Tech. Rep. MCEER-98-0007, Multidisciplinary Ctr. for Earthquake Engrg. Res., State University of New York at Buffalo, Buffalo, N.Y.
10.
Koh, S. K., and Stephen, R. I. ( 1991). “Mean stress effects on low-cycle fatigue for a high strength steel.” Fatigue Fracture of Engrg. Mat. and Struct., 14(4).
11.
Mander, J. B., and Cheng, C. T. ( 1995). “Renewable hinge detailing for bridge columns.” Proc., Pacific Conf. on Earthquake Engrg., Australian Earthquake Engineering Society, Parkville, Australia.
12.
Mander, J. B., Panthaki, F. D., and Kasalanati, A. (1994). “Low cycle fatigue behavior of reinforcing steel.”J. Mat. in Civ. Engrg., ASCE, 6(4), 453–468.
13.
Mander, J. B., Pekcan, G., and Chen, S. S. ( 1995). “Low-cycle variable amplitude fatigue modeling of top-and-seat angle connections.” Engrg. J., 32(2).
14.
Mander, J. B., Priestley, M. J. N., and Park, R. ( 1984). “Seismic design of bridge piers.” Res. Rep. 84-2, Dept. of Civ. Engrg., University of Canterbury, Christchurch, N.Z.
15.
Mander, J. B., Priestley, M. J. N., and Park, R. (1988a). “Theoretical stress strain model for confined concrete.”J. Struct. Engrg., ASCE, 114(8), 1804–1826.
16.
Mander, J. B., Priestley, M. J. N., and Park, R. (1988b). “Observed stress strain behavior of confined concrete.”J. Struct. Engrg., ASCE, 114(8), 1827–1849.
17.
Manson, S. S. ( 1953). “Behavior of metals under conditions of thermal stress.” Proc., Heat Transfer Symp., University of Michigan Engineering Research Institute, Ann Arbor, Mich.
18.
Miner, M. A. ( 1945). “Cumulative damage in fatigue.” Trans. ASME, 67.
19.
Park, R., and Paulay, T. ( 1975). Reinforced concrete structures, Wiley, New York.
20.
Paulay, T., and Priestley, M. J. N. ( 1992). Seismic design of reinforced concrete and masonry structures, Wiley, New York.
21.
Priestley, M. J. N., Seible, F., Xiao, Y., and Verma, R. ( 1994a). “Steel jacketed retrofitting of reinforced concrete bridge columns for enhanced shear strength. Part I: Theoretical considerations and test design.” ACI Struct. J., 91(4).
22.
Priestley, M. J. N., Seible, F., Xiao, Y., and Verma, R. ( 1994b). “Steel jacketed retrofitting of reinforced concrete bridge columns for enhanced shear strength. Part II: Test results and comparison with theory.” ACI Struct. J., 91(5).
23.
Uang, C. M., and Bertero, V. V. ( 1990). “Evaluation of seismic energy in structures.” Earthquake Engrg. and Struct. Dyn., 19.
24.
Watson, S., Zahn, F. A., and Park, R. (1994). “Simulated seismic load tests on reinforced concrete columns.”J. Struct. Engrg., ASCE, 120(6), 1825–1849.
25.
Yuk, L. W. ( 1990). “Squat circular bridge piers under multi-directional seismic attack.” PhD thesis, Dept. of Civ. Engrg., University of Canterbury, Christchurch, N.Z.
26.
Zahn, F. A. ( 1986). “Design of reinforced concrete bridge columns for strength and ductility.” Res. Rep. 86-7, Dept. of Civ. Engrg., University of Canterbury, Christchurch, N.Z.
Information & Authors
Information
Published In
History
Received: Oct 14, 1999
Published online: Dec 1, 2001
Published in print: Dec 2001
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.