Steel Moment Frames for Earthquakes in United States and Japan
Publication: Journal of Structural Engineering
Volume 126, Issue 8
Abstract
Steel moment frames are used for seismic design in the United States and Japan and are highly regarded structural systems, but severe damage to steel frames occurred during the 1994 Northridge and 1995 Hyogoken-Nanbu earthquakes. Examination of similarities and differences in the engineering research and practice for these frames in the two countries provides insight into this important seismic issue. A brief history of the engineering practice in both countries is provided, and current practice and design methods are summarized and compared. The evolution of structural systems and the details and practices employed in the two countries are described. Damage from past earthquakes is briefly reviewed. Welding processes and material behavior are also compared, because they influence the seismic behavior of these systems. Many U.S. engineers believe that Japanese buildings are much stiffer and stronger but less ductile than comparable U.S. buildings. It will be shown that this is not always the case. Significant differences in U.S. and Japanese design practices will be shown, but even greater similarities in our structures and design procedures will be noted. As a consequence, this paper should help engineers from both countries learn from one another.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
AIJ standards for structural calculation of steel reinforced concrete structures. (1958). Architectural Institute of Japan, Tokyo (in Japanese).
2.
Baba, T., et al. (1969). “Fuji nongas wire NA-50.” Fuji Tech. Rep., 14(2), 250–265 (in Japanese).
3.
Bonowitz, D., and Youssef, N. (1995). “SAC survey of steel moment-resisting frame buildings affected by the 1994 Northridge earthquake.” Tech. Rep. 95-06: Surveys and Assessment of Damage to Build. Affected by the Northridge Earthquake of January 17, 1994, SAC Joint Venture, Sacramento, Calif., 2.1–2.169.
4.
Full-scale test on plastic rotation capacity of steel wide-flange beams connected with square tube steel columns. (1997). Kinki Branch, Architectural Institute of Japan, Osaka, Japan (in Japanese with attached abridged English version).
5.
Funabashi, I., and Maruoka, Y. (1970). “Non-gas semi-automatic welding method.” Rep. of Takenaka Tech. Res. Lab., Tokyo, Japan, 97, 1–17 (in Japanese).
6.
Guidelines for plastic design of steel building structures. (1975). Architectural Institute of Japan, Tokyo (in Japanese).
7.
Interim guidelines: evaluation, repair, modification and design of welded steel moment frame structures (August 1995), plus Interim Guidelines Advisory No. 1 (March 1997). (1997). Federal Emergency Management Agency, Washington, D.C.
8.
Manual for semi-automatic CO2 shielded metal arc welding. (1994). Japan Welding Engineering Society, Tokyo (in Japanese).
9.
Measurement of chemical and mechanical properties for structural steel plates. (1995). Kawasaki Heavy Industry, Tokyo (in Japanese).
10.
Morita, K. et al. (1988). “Discussion on new technologies regarding field welding.” J. Steel Struct. Technol., Kokozo Shuppan, Tokyo, 19–30 (in Japanese).
11.
Nakashima, M., Inoue, K., and Tada, M. (1998). “Classification of damage to steel buildings observed in the 1995 Hyogoken-Nanbu earthquake.” J. Engrg. Struct., 20(4–6), 271–281.
12.
Nakashima, M., and Sawaizumi, S. (2000). “Column-to-beam strength ratio required for ensuring beam-collapse mechanisms in earthquake responses of steel moment frames.” Proc., 12th World Conf. on Earthquake Engrg., International Association for Earthquake Engineering, Tokyo, Paper #1109/6/A.
13.
“Progress report in 1997.” (1997). Rep. of Welding Res., Japan Welding Engrg. Soc., Tokyo, 30 (in Japanese).
14.
Reconnaissance report on damage to steel building structures observed from the 1995 Hyogoken-Nanbu Earthquake. (1995). Kinki Branch, Architectural Institute of Japan, Osaka, Japan (in Japanese with attached abridged English version).
15.
Roeder, C. W., and Foutch, D. F. (1996). “Experimental results for seismic resistant steel moment frame connections.”J. Struct. Engrg., ASCE, 122(6), 581–588.
16.
Seismic provisions for structural steel buildings. (1997). American Institute of Steel Construction, Chicago.
17.
Standard for limit state design of steel structures (draft). (1990). Architectural Institute of Japan, Tokyo (in Japanese).
18.
Statistical analysis of Charpy V-notch toughness for steel wide flange structural shapes. (1995). American Institute of Steel Construction, Chicago.
19.
Structural provisions for building structures—1997 Edition. (1997). Building Center of Japan, Tokyo (in Japanese).
20.
Technical recommendations for steel construction for buildings (part 1 guide to steel-rib fabrication). (1996). 4th Ed., Architectural Institute of Japan, Tokyo (in Japanese).
21.
Uniform building code, volume 2. (1997). International Conference of Building Officials, Whittier, Calif.
Information & Authors
Information
Published In
History
Received: Jul 19, 1999
Published online: Aug 1, 2000
Published in print: Aug 2000
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.