Strength and Stiffness of Oak Pegs in Traditional Timber-Frame Joints
Publication: Journal of Structural Engineering
Volume 126, Issue 6
Abstract
The objectives of this paper are to present experimental data and analytical models to assist in the analysis and design of pegged joints in traditional timber frames. Seventy-two simplified mortise and tenon joints were loaded to failure under compression-induced double shear. Load, deformation, and time were recorded. All joints utilized 25.4-mm-diameter red oak pegs, typical of those used in modern timber-frame construction in North America. Half of the specimens were made with eastern white pine lumber, with the remaining specimens made of sugar maple. All specimens had 50.8 mm center pieces simulating a typical tenon. Side pieces were evenly divided into 25.4 mm and 50.8 mm thicknesses. Half of the specimens were arranged such that the center piece was loaded parallel to the grain and the side pieces perpendicular. Grain orientation was reversed for the remaining specimens. Joint stiffness was estimated by a regression analysis of the linear portion of the load-slip curves. A model for joint stiffness was developed for use in analysis of traditional timber frames. The stiffness model was found to underestimate the stiffness of typical pegged knee-brace joints by 20–30%. The yield theory was augmented with two peg deformation modes to develop a method for predicting failure loads. Strength predictions ranged from 16% low to 2% high in comparison with the test data.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
AF&PA. (1997). National design specification for wood construction, American Forest & Paper Association, Washington, D.C.
2.
AITC. (1994). Timber construction manual, 4th Ed., American Institute of Timber Construction, Englewood, Colo.
3.
ASCE. (1995). “Standard for load and resistance design (LRFD) for engineered wood construction.” AF&PA/ASCE 16-95, American Society of Civil Engineers, Reston, Va.
4.
Benson, T., and Gruber, J. (1980). Building the timber frame house, Charles Scribner's Sons, New York.
5.
Brungraber, R. L. ( 1985). “Traditional timber joinery: A modern analysis.” PhD dissertation, Stanford University, Palo Alto, Calif.
6.
Bulleit, W. M., Sandberg, L. B., O'Bryant, T. L., Weaver, D. A., and Pattison, W. E. (1996). “Analysis of frames with traditional timber connections.” Proc., 1996 Int. Wood Engrg. Conf., Vol. 4, Omnipress, Madison, Wis., 232–239.
7.
Bulleit, W. M., Sandberg, L. B., Drewek, M. W., and O'Bryant, T. L. (1999). “Behavior and modeling of wood-pegged timber frames.”J. Struct. Engrg., ASCE, 125(1), 3–9.
8.
Church, J. R., and Tew, B. W. (1997). “Characterization of bearing strength factors for pegged timber connections.”J. Struct. Engrg., ASCE, 123(3), 326–332.
9.
Kessel, M. H., and Augustin, R. (1995a). “Load behavior of connections with pegs I.” Trans. by M. Peavy and R. Schmidt, Timber Framing, 38, 6–9.
10.
Kessel, M. H., and Augustin, R. (1995b). “Load behavior of connections with pegs II.” Trans. by M. Peavy and R. Schmidt, Timber Framing, 39, 8–10.
11.
McLain, T. E., and Thangjitham, S. (1983). “Bolted wood-joint yield model.”J. Struct. Engrg., ASCE, 109(8), 1820–1835.
12.
NFPA. ( 1991). National design specification for wood construction, National Forest Products Association, Washington, D.C.
13.
Reid, E. H. ( 1997). “Behavior of wood pegs in traditional timber frame connections.” Masters thesis, Michigan Technological University, Houghton, Mich.
14.
Sandberg, L. B., Bulleit, W. M., O'Bryant, T. L., Postlewaite, J. J., and Schaffer, J. J. (1996). “Experimental investigation of traditional timber connections.” Proc., 1996 Int. Wood Engrg. Conf., Omnipress, Madison, Wis., Vol. 4, 225–231.
15.
Schmidt, R. J., and MacKay, R. B. (1997). Timber frame tension joinery, University of Wyoming, Laramie, Wyo.
16.
Schmidt, R. J., and Daniels, C. E. (1999). Design considerations for mortise and tenon connections, University of Wyoming, Laramie, Wyo.
17.
Soltis, L. A., Hubbard, F. K., and Wilkinson, T. L. (1986). “Bearing strength of bolted timber joints.”J. Struct. Engrg., ASCE, 112(9), 2141–2154.
18.
Soltis, L. A., and Wilkinson, T. L. (1991). “United States application of European yield model to large-diameter dowel fastener specification.” Proc., 1991 Int. Timber Engrg. Conf., TRADA, London, Vol. 3, 43–49.
19.
USFPL. ( 1974). Wood handbook: Wood as an engineering material. Agricultural Handbook No. 72, U.S. Forest Products Laboratory, Madison, Wis.
Information & Authors
Information
Published In
History
Received: Aug 10, 1999
Published online: Jun 1, 2000
Published in print: Jun 2000
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.