Seismic Behavior of Composite RCS Frame Systems
Publication: Journal of Structural Engineering
Volume 126, Issue 4
Abstract
This paper presents the results of an experimental investigation into the seismic performance of a composite moment resisting frame system that consists of reinforced concrete columns (with an embedded steel shape for erection purposes) and composite steel beam-reinforced concrete slab sections. Quasi-static reversed cyclic loading was performed on six two-thirds-scale subassemblage specimens. Various detailing options were evaluated to provide full moment connection in both orthogonal framing directions at the beam-column joints. With appropriate joint detailing, specimens exhibited a desirable beam plastic hinge mechanism with stable hysteretic response. Composite beam sections maintained near full composite behavior beyond code based drift limits with good energy dissipation characteristics and were able to undergo large plastic rotation magnitudes. This framing system may represent a viable alternative for low-to-mid-rise structures in high seismic risk zones.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
ASCE Task Committee on Design Criteria for Composite Structures in Steel and Concrete. (1994). “Guidelines for design of joints between steel beams and reinforced concrete columns.”J. Struct. Engrg., ASCE, 120(8), 2330–2357.
2.
Bracci, J. M., Moore, W. P., and Bugeja, M. N. (1999). “Seismic design and constructability of RCS special moment frames.”J. Struct. Engrg., ASCE, 125(4), 385–392.
3.
“Building code requirements for structural concrete and commentary.” (1995). ACI 318, American Concrete Institute, Farmington Hills, Mich.
4.
Deierlein, G. G., Sheikh, T. M., Yura, J. A., and Jirsa, J. O. (1989). “Beam-column moment connections for composite frames: Part 2.”J. Struct. Engrg., ASCE, 115(11), 2877–2896.
5.
Design guidelines for composite RCS joints. (1994). H. Kuramoto, S. Mehanny, and G. Deierlein, translators, Composite RCS Structures Subcommittee, Architectural Institute of Japan, Tokyo.
6.
Griffis, L. G. (1986). “Some design considerations for composite-frame structures.” AISC/Engrg. J., Second Quarter, 59–64.
7.
Kanno, R. ( 1993). “Strength, deformation, and seismic resistance of joints between steel beams and reinforced concrete columns,” PhD dissertation, Cornell University, Ithaca, N.Y.
8.
Leon, R. T., Hajjar, J. F., and Gustafson, M. A. (1998). “Seismic response of composite moment-resisting connections. I: Performance.”J. Struct. Engrg., ASCE, 124(8), 868–876.
9.
Manual of steel construction—load and resistance factor design (LRFD). (1994). American Institute of Steel Construction, Chicago.
10.
“Minimum design loads for buildings and other structures.” (1995). ASCE 7-95. ASCE, New York.
11.
“NEHRP recommended provisions for seismic regulations for new buildings and other structures: Part 1—Provisions and Part 2—Commentary.” (1997). Publ. Nos. 302 and 303, Federal Emergency Management Agency, Washington, D.C.
12.
Nishiyama, I., Itadani, H., and Sugihiro, K. (1998). “Bi-directional seismic response of reinforced concrete column and structural steel beam subassemblages.” Proc., Struct. Engrg. World Conf., Elvesier Sciences, New York.
13.
Sakaguchi, N., Tominaga, H., Murai, Y., Takase, Y., and Shuto, K. (1988). “Strength and ductility of steel beam-RC column joint.” Proc., 9th World Conf. on Earthquake Engrg., Vol. 4, 713–718.
14.
Sheikh, T. M., Deierlein, G. G., Yura, J. A., and Jirsa, J. O. (1989). “Beam-column moment connections for composite frames: Part 1.”J. Struct. Engrg., ASCE, 115(11), 2858–2876.
15.
Specifications and commentaries for composite steel floor deck. (1989). Steel Deck Institute, Canton, Ohio.
16.
Uchida, K., and Noguchi, H. (1998). “Nonlinear three-dimensional finite element analysis of RCS frame.” Proc., 5th Joint Tech. Coordinating Com. Meeting, U.S.-Japan Cooperative Earthquake Research Program on Composite and Hybrid Structures, Tokyo.
17.
U.S.-Japan Planning Groups—Joint Planning Workshop. (1992). “Recommendations for U.S.-Japan cooperative research program—phase 5 composite and hybrid structures.” Tech. Rep. No. UMCEE 92-29, University of Michigan, Ann Arbor, Mich.
18.
Viest, I. M., Colaco, J. P., Furlong, R. W., Griffis, L. G., Leon, R. T., and Wyllie, L. A. (1997). Composite construction design for buildings. ASCE/McGraw Hill, New York.
Information & Authors
Information
Published In
History
Received: Dec 16, 1998
Published online: Apr 1, 2000
Published in print: Apr 2000
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.