Local Buckling of Side-Plated Reinforced-Concrete Beams. I: Theoretical Study
Publication: Journal of Structural Engineering
Volume 125, Issue 6
Abstract
Steel plates can be bolted to the sides of reinforced-concrete beams to both strengthen and stiffen them. When these side-plated beams are subject to their intended design actions, compression, bending, and shear stresses are produced in the steel plates and this can lead to instability by local buckling of the plates. This type of buckling problem is known as a contact problem, since the plate is constrained to buckle in only one lateral direction. The paper presents a Rayleigh-Ritz method of the local buckling analysis of rectangular unilaterally restrained plates in compression, bending, and shear. Polynomials are used to define the displacement function, while the restraining medium is modeled as a tensionless foundation. The method is shown to be very efficient computationally, and elastic local buckling coefficients are presented for a variety of restraint cases for various plate aspect ratios, in terms of interaction diagrams. The buckling model is shown to be in good agreement with experimental results from the full-scale testing of two side-plated reinforced-concrete beams, as presented in a companion paper.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Ascione, L., and Grimaldi, A. ( 1984). “Unilateral contact between a plate and an elastic foundation.” Meccanica, 19, 223–233.
2.
Baniotopoulos, C. C., Abdalla, K. M., and Panagiotopoulos, P. D. ( 1994). “A variational inequality and quadratic programming approach to the separation problem of steel bolted brackets.” Comp. and Struct., 53(4), 983–991.
3.
Bathe, K. J., and Chaudhary, A. ( 1985). “A solution method for planar and axisymmetric contact problems.” Int. J. Numer. Methods in Engrg., 21, 65–88.
4.
Bezine, G. ( 1988). “A new boundary element method for bending of plates on elastic foundations.” Int. J. Solids and Struct., 24, 557–565.
5.
Bradford, M. A., Wright, H. D., and Uy, B. ( 1997). “Short and long-term behaviour of axially loaded composite profiled walls.” Proc., Instn. of Civ. Engrgs., London, Struct. and Build., 128(1), 26–37.
6.
Bridge, R. Q., O'Shea, M. D. O., Gardner, A. P., Grigson, R., and Tyrrell, J. ( 1995). “Local buckling of square thin-walled tubes with concrete infill.” Proc., Int. Conf. on Struct. Stability and Des., Kitipornchai, Hancock, and Bradford, eds., Balkema, Rotterdam, The Netherlands, 307–314.
7.
Bruno, D., and Grimaldi, A. ( 1990). “Delamination failure of layered composite plates loaded in compression.” Int. J. Solids and Struct., 26(3), 313–330.
8.
Celep, Z. (1988a). “Circular plate on tensionless Winkler foundation.”J. Engrg. Mech., ASCE, 114(10), 1723–1739.
9.
Celep, Z. (1988b). “Rectangular plates resting on tensionless elastic foundation.”J. Engrg. Mech., ASCE, 114(12), 2083–2092.
10.
Chai, H. ( 1990a). “Buckling and postbuckling of elliptical plates: Part 1—analysis.” J. Appl. Mech., 57, 981–988.
11.
Chai, H. ( 1990b). “Buckling and postbuckling of elliptical plates: Part 2—results.” J. Appl. Mech., 57, 989–994.
12.
Chai, H., Babcock, C. D., and Knauss, W. G. ( 1981). “One dimensional modelling of failure in laminated plates by delamination buckling.” Int. J. Solids and Struct., 17(11), 1069–1083.
13.
Chand, R., Hang, E. K., and Rim, K. ( 1976). “Analysis of unbound contact problems by means of quadratic programming.” J. Optimal Theory Applic., 20, 171–189.
14.
Cheung, Y. K., and Zienkiewicz, O. C. ( 1965). “Plates and tanks on elastic foundations—an application of the finite element method.” Int. J. Solids and Struct., 1, 451–461.
15.
Cheung, Y. K., and Nag, D. K. ( 1968). “Plates and beams on elastic foundation—linear and nonlinear behaviour.” Geotechnique, London, 18, 250–260.
16.
Coury, T. F., and Seireg, A. ( 1971). “A mathematical programming method for design of elastic bodies in contact.” J. Appl. Mech., 2, 387–392.
17.
Fischer, U., and Melosh, R. J. ( 1987). “Solving discretised contact problems using linear programming.” Comp. and Struct., 25, 661–664.
18.
Hobbs, R. E. ( 1989). “Two-dimensional upheaval buckling of a heavy sheet.” Thin-Walled Struct., 8, 235–252.
19.
Kastikadelis, J. T., and Kallivokas, L. E. ( 1986). “Clamped plates on Pasternak-type elastic foundation by the boundary element method.” J. Appl. Mech., 53, 909–917.
20.
Kerr, A. D. ( 1979). “On thermal buckling of straight railroad tracks and the effect of track length on the track response.” Rail Int., 9, 759–768.
21.
Khathlan, A. A. (1994). “Large-deformation analysis of plates on unilateral elastic foundation.”J. Engrg. Mech., ASCE, 120(8), 1820–1827.
22.
Khathlan, A. A., and Waly, H. A. ( 1994). “Nonaxisymmetric unbonded contact of plates on tensionless Winkler foundations.” Mech. of Struct. and Machines, 22(3), 263–281.
23.
Koo, J. S., and Kwak, B. M. ( 1995). “Post-buckling analysis of nonfrictional contact problems using linear complementarity formulation.” Comp. and Struct., 15(5), 783–794.
24.
Lewandowski, R., and Switka, R. ( 1991). “Unilateral plate contact with the elastic-plastic Winkler-type foundation.” Comp. and Struct., 39(6), 641–651.
25.
Liew, K. M., Lam, K. Y., and Chow, S. T. ( 1990). “Free vibration analysis of rectangular plates using orthogonal plate functions.” Comp. and Struct., 34, 79–85.
26.
Liew, K. M., and Wang, C. M. ( 1993). “pb-2 Rayleigh-Ritz method for general plate analysis.” Engrg. Struct., 15, 55–60.
27.
Liew, K. M., and Wang, C. M. ( 1995). “Elastic buckling of regular polygonal plates.” Thin-Walled Struct., 21, 1630–173.
28.
Oden, J. T., and Kikuchi, N. ( 1982). “Finite element methods for constrained problems in elasticity.” Int. J. Numer. Methods in Engrg., 18, 701–725.
29.
Oehlers, D. J., Wright, H. D., and Burnet, M. J. (1994). “Flexural strength of profiled beams.”J. Struct. Engrg., ASCE, 120(2), 378–393.
30.
Ohtake, K., Oden, J. T., and Kikuchi, N. ( 1980a). “Analysis of certain unilateral problems in Von Karman plate theory by a penalty method—Part 1. A variational principle with penalty.” Comp. Methods in Appl. Mech. and Engrg., 24, 187–213.
31.
Ohtake, K., Oden, J. T., and Kikuchi, N. ( 1980b). “Analysis of certain unilateral problems in Von Karman plate theory by a penalty method—Part 2. Approximation and numerical analysis.” Comp. Methods in Appl. Mech. and Engrg., 24, 317–337.
32.
Panagiotopoulos, P. D. ( 1985). Inequality problems in mechanics and applications—convex and nonconvex energy functions. Birkhauser, New York.
33.
Rao, N. S. V. K. ( 1974). “Onset of separation between a beam and a tensionless elastic foundation due to moving loads.” J. Appl. Mech., 41(2), 303–305.
34.
Roorda, J. ( 1988). “Buckles, bulges, and blow-ups.” Applied solid mechanics-2, Tooth and Spence, eds., Elsevier Science, London, 347–380.
35.
Shahwan, K. W., and Waas, A. M. ( 1994). “A mechanical model for the buckling of unilaterally constrained rectangular plates.” Int. J. Solids and Struct., 31(1), 75–87.
36.
Simo, J. C., and Laursen, T. A. ( 1992). “An augmented Lagrangian treatment of contact problems involving friction.” Comp. and Struct., 42, 97–116.
37.
Smith, S. T., Bradford, M. A., and Oehlers, D. J. ( 1996). “Buckling of bolted and glued side plates used for the strengthening of reinforced concrete beams.” Proc., 3rd Asian-Pacific Conf. on Computat. Mech., Balkema, Rotterdam, The Netherlands, 291–297.
38.
Smith, S. T., Bradford, M. A., and Oehlers, D. J. (1999). “Local buckling of side-plated reinforced concrete beams. II: Experimental study.”J. Struct. Engrg., ASCE, 126(6), 635–643.
39.
Stein, E., and Wriggers, P. ( 1984). “Stability of rods with unilateral constraints: A finite element solution.” Comp. and Struct., 19(1, 2), 205–211.
40.
Swartz, S. E., and O'Neill, R. J. ( 1995). “Linear elastic buckling of plates subjected to combined loads.” Thin-Walled Struct., 21, 1–15.
41.
Thomopoulos, K., and Bisbos, C. D. ( 1993). “Unilateral contact stresses at steel pipe saddles.” Thin-Walled Struct., 15, 305–319.
42.
Timoshenko, S. P., and Gere, J. M. ( 1963). Theory of elastic stability . McGraw-Hill, New York.
43.
Tsai, N., and Westmann, R. (1967). “Beams on tensionless foundation.”J. Engrg. Mech., ASCE, 93, 1–12.
44.
Uy, B., and Bradford, M. A. ( 1994). “Local buckling of composite steel-concrete rectangular columns.” Proc., 5th Int. Conf. on Steel Struct., C. I. Premiere Pte Ltd., Singapore, 313–322.
45.
Uy, B., and Bradford, M. A. ( 1995). “Local buckling of thin steel plates in composite construction: experimental and theoretical study.” Proc., Instn. of Civ. Engrgs., London, Struct. and Build., 110(4), 426–440.
46.
Uy, B., and Bradford, M. A. ( 1996). “Elastic local buckling of steel plates in composite steel-concrete members.” Engrg. Struct., 18(3), 193–200.
47.
Villaggio, O. ( 1983). “A free boundary value problem in plate theory.” J. Appl. Mech., 50, 297–302.
48.
Wang, C. M., and Liew, K. M. ( 1994). “Buckling of triangular plates under uniform compression.” Engrg. Struct., 16(1), 43–50.
49.
Weitsman, Y. ( 1970). “On foundations that react on compression only.” J. Appl. Mech., 37, 1019–1030.
50.
Wright, H. D. ( 1993). “Buckling of plates in contact with a rigid medium.” The Struct. Engr., 71(12), 209–215.
51.
Wright, H. D. (1995). “Local stability of filled and encased steel sections.”J. Struct. Engrg., ASCE, 121(10), 1382–1388.
52.
Yun, H. D., and Kyriakides, S. (1985). “Model for beam-mode buckling of buried pipelines.”J. Engrg. Mech., ASCE, 111, 235–253.
Information & Authors
Information
Published In
History
Received: Jan 22, 1998
Published online: Jun 1, 1999
Published in print: Jun 1999
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.