Wind Load Statistics for Probability-Based Structural Design
Publication: Journal of Structural Engineering
Volume 125, Issue 4
Abstract
ASCE Standard 7, “Minimum Design Loads for Buildings and Other Structures,” has contained provisions for load combinations and load factors suitable for load and resistance factor design since its 1982 edition. Research in wind engineering in the intervening years has raised questions regarding the wind load factor 1.3 and load combinations in which the wind load appears in ASCE 7-95. This paper presents revised statistical models of wind load parameters based on more recent research and a Delphi, and reassesses the wind load combinations in ASCE Standard 7 probabilistically. The current approach to specifying wind loads in ASCE 7 does not lead to uniform reliability in inland and hurricane-prone regions of the country. It is recommended that the factor accounting for wind directionality effects should be separated from the load factor and presented in a separate table in the wind load section, that the wind load factor should be increased from 1.3 to approximately 1.5 or 1.6 to achieve reliability consistent with designs governed by gravity load combinations, and that the exposure classification procedure in ASCE Standard 7 should be revised to reduce the current high error rate in assigning exposures.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Algermissen, S. T., and Perkins, D. M. ( 1976). “A probabilistic estimate of maximum acceleration in rock in the contiguous United States.” Open File Rep. 76-416, U.S. Geological Survey, Denver, Colo.
2.
Batts, M., Russell, L. R., and Simiu, E. (1980). “Hurricane wind speeds in the United States.”J. Struct. Div., ASCE, 100(10), 2001–2015.
3.
Cook, N. J., and Mayne, J. R. ( 1979). “A novel working approach to the assessment of wind loads for equivalent static design.” J. Wind Engrg. and Indust. Aerodyn., 4, 149–164.
4.
Corotis, R. B., Fox, R. R., and Harris, J. C. (1981). “Delphi methods: theory and design load application.”J. Struct. Div., ASCE, 107(6), 1095–1105.
5.
Davenport, A. G., Isyumov, N., and Surry, D. ( 1979). “The role of wind tunnel studies in design against wind.” Proc., ASCE Spring Convention, ASCE, Reston, Va.
6.
Ellingwood, B. (1981). “Wind and snow load statistics for probabilistic design.”J. Struct. Div., ASCE, 107(7), 1345–1349.
7.
Ellingwood, B. ( 1994). “Probability-based codified design: past accomplishments and future challenges.” Struct. Safety, 13(3), 159–176.
8.
Ellingwood, B., MacGregor, J. G., Galambos, T. V., and Cornell, C. A. (1982). “Probability-based load criteria: load factors and load combinations.”J. Struct. Div., ASCE 108(5), 978–997.
9.
Ellingwood, B., and Tekie, P. B. ( 1997). “Wind load statistics for probability-based structural design.” Report Prepared for National Home Builders Association Research Center, National Technical Information Service, Springfield, Va.
10.
Federal Emergency Management Agency (FEMA). ( 1994). “NEHRP recommended provisions for the development of seismic regulations for new buildings.” FEMA Rep. 223, Washington, D.C.
11.
Galambos, T. V., Ellingwood, B., MacGregor, J. G., and Cornell, C. A. (1982). “Probability-based load criteria: assessment of current design practice.”J. Struct. Div., ASCE, 108(5), 959–977.
12.
Hart, G., and Ellingwood, B. ( 1982). “Reliability-based design considerations for relating loads measured in wind tunnel to structural resistance.” Wind tunnel modeling for civil engineering applications, T. A. Reinhold, ed., Cambridge University Press, New York, 27–42.
13.
Hwang, H., et al. ( 1983). “A consensus estimation study of nuclear power plant structural loads.” Rep. NUREG/CR-3315, U.S. Nuclear Regulatory Commission, Washington, D.C.
14.
Lind, N. C., and Nowak, A. S. (1986). “Pooling expert opinions on probability distributions.”J. Engrg. Mech., ASCE, 114(2), 328–341.
15.
Load and resistance factor design specification for structural steel buildings. (1993). American Institute of Steel Construction, Chicago.
16.
Marshall, R. D. ( 1977). “The measurement of wind loads on a full-scale mobile home.” Rep. NBSIR 77-1289, National Bureau of Standards, Washington, D.C.
17.
Mehta, K. C. (1984). “Wind load provisions for ANSI A58.1-1982.”J. Struct. Engrg., ASCE, 110(4), 769–784.
18.
“Minimum design loads for buildings and other structures.” (1996). ASCE 7-95, ASCE, Reston, Va.
19.
Naess, A. ( 1996). “A method for extrapolation of extreme value data.” Engrg. Mechanics: Proc., 11th Specialty Conf., ASCE, Reston, Va., 273–276.
20.
Peterka, J., and Cermak, J. E. (1976). “Wind pressures on buildings—probability densities.”J. Struct. Div., ASCE, 101(6), 1255–1267.
21.
Peterka, J., and Shahid, S. (1998). “Design gust wind speeds in the U.S.”J. Struct. Engrg., ASCE, 124(2), 207–214.
22.
Ravindra, M. K., Galambos, T. V., and Cornell, C. A. (1978). “Wind and snow load factors for use in LRFD.”J. Struct. Div., ASCE, 104(9), 1443–1457.
23.
Rosowsky, D., and Ellingwood, B. ( 1992). “Reliability of wood systems subjected to stochastic live loads.” Wood and Fiber Sci., 24(1), 47–59.
24.
Shinozuka, M. (1983). “Basic analysis of structural safety.”J. Struct. Engrg., ASCE, 109(3), 721–740.
25.
Shooman, M., and Sinkar, S. ( 1977). “The use of consensus in analytical safety.” Rep. POLY-EE-77-305, Polytechnic Institute of New York, Brooklyn, N.Y.
26.
Simiu, E., Changery, M., and Filliben, J. J. (1980). “Extreme wind speeds at 129 stations in the contiguous United States.”J. Struct. Div., ASCE, 106(4), 809–817.
27.
Simiu, E., et al. (1985). “Multivariate distributions of directional wind speeds.”J. Struct. Engrg., ASCE, 111(4), 939–943.
28.
Simiu, E., and Filliben, J. J. (1976). “Probability distributions of extreme wind speeds.”J. Struct. Div., ASCE, 102(9), 1861–1877.
29.
Simiu, E., and Filliben, J. J. ( 1981). “Wind direction effects on cladding and structural loads.” Engrg. Struct., 3, 181–186.
30.
Simiu, E., and Heckert, N. A. (1996). “Extreme wind distribution tails: a `peaks over threshold' approach.”J. Struct. Engrg., ASCE, 122(5), 539–547.
31.
Simiu, E., Leigh, S., and Nolan, W. (1986). “Environmental load direction and reliability bounds.”J. Struct. Engrg., ASCE, 112(5), 1199–1203.
32.
“Standard for load and resistance factor design (LRFD) for engineered wood construction.” (1996). AF&PA/ASCE 16-95, ASCE, Reston, Va.
33.
Stathopoulos, T. (1980). “PDF of wind pressures on low-rise buildings.”J. Struct. Div., ASCE, 106(5), 973–990.
34.
Thom, H. C. S. (1968). “New distribution of extreme winds in the United States.”J. Struct. Div., ASCE, 94(7), 1787–1801.
35.
Vickery, P. J., and Twisdale, L. A. (1995). “Prediction of hurricane wind speeds in the United States.”J. Struct. Engrg., ASCE, 121(11), 1691–1699.
36.
Wen, Y. K. (1983). “Wind direction and structural reliability.”J. Struct. Div., ASCE, 109(4), 1028–1041.
37.
Wen, Y. K. (1984). “Wind direction and structural reliability. II.”J. Struct. Div., ASCE, 110(6), 1253–1264.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 125 • Issue 4 • April 1999
Pages: 453 - 463
History
Received: Apr 16, 1998
Published online: Apr 1, 1999
Published in print: Apr 1999
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.