Thin-Walled Beam-Columns. II: Proportional Loading Tests
Publication: Journal of Structural Engineering
Volume 125, Issue 11
Abstract
This paper presents tests on thin-walled I-sections in combined compression and minor axis bending. The tests were conducted in a rig consisting of two interlinked actuators applying axial force and end moment. The tests involved pure compression, combined compression and bending, and pure bending. The test results are compared with the design strengths of the Australian Standard for Steel Structures AS4100, the AISC-LRFD Specification, and Eurocode 3, Part 1.1. It is shown that the experimental interaction curve is close to being linear in the intermediate and long slenderness ranges. The design interaction curves of AS4100, the AISC-LRFD Specification, and Eurocode 3 are shown to be conservative in all cases, particularly in the high moment regions. The conservatism is attributed to the definition of the design bending section capacity in the three specifications. Proposals that increase the bending section capacity are presented based on the behavior observed during the tests. The resulting moment–axial force interaction curves are conservative and in reasonable agreement with the tests.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Chick, C. G., and Rasmussen, K. J. R. (1995). “Tests of thin-walled I-sections in combined compression and minor axis bending, Part II—Proportional loading tests.” Res. Rep. R717, School of Civ. and Min. Engrg., University of Sydney, Sydney, Australia.
2.
Chick, C. G., and Rasmussen, K. J. R. (1999). “Thin-walled beam-columns: Sequential loading and moment gradient tests.”J. Struct. Engrg., ASCE, 125(11), 1257–1266.
3.
Davids, A. J., and Hancock, G. J. (1986a). “Compression tests of long welded I-section columns.”J. Struct. Engrg., ASCE, 112(10), 2281–2297.
4.
Davids, A. J., and Hancock, G. J. (1986b). “Compression tests of short welded I-sections.”J. Struct. Engrg., ASCE, 112(5), 960–976.
5.
“Design of steel structures, Part 1.1—General rules and rules for buildings.” (1992). Eurocode3, Draft document ENV 1993-1-1, European Committee for Standardisation, Brussels, Belgium.
6.
“Design of steel structures, Part 1.3—Cold formed thin gauge members and sheeting.” (1996). Eurocode3, Draft document ENV 1993-1-3, European Committee for Standardisation, Brussels, Belgium.
7.
Galambos, T. V. (1988). Guide to stability design criteria for metal structures, 4th Ed., Wiley, New York.
8.
Hancock, G. J. ( 1985). Submission concerning Table 1 of Doc BD/1/84-15—Section slenderness limits for plates supported on one edge and subjected to bending in-plane, presented to BD/1 committee of Standards Australia at the meeting of 9 May 1985, Standards Australia, Sydney.
9.
“Load and resistance factor design specification for structural steel buildings.” (1993). American Institute of Steel Construction, Chicago.
10.
Rhodes, J. (1982). “The Post-buckling Behaviour of Bending Elements.” W.-W. Yu and J. H. Senne, eds., Proc., 6th Int. Spec. Conf. on Cold-formed Steel Struct., 135–155.
11.
“Steel structures.” (1998). AS4100, Standards Australia, Sydney, Australia.
Information & Authors
Information
Published In
History
Received: Aug 26, 1998
Published online: Nov 1, 1999
Published in print: Nov 1999
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.