Performance of Profiled Concrete Shear Panels
Publication: Journal of Structural Engineering
Volume 124, Issue 4
Abstract
This paper describes the behavior of profiled concrete shear panels that may be used as core walls in framed construction. This research developed as a part of a larger program of work on a novel form of composite walling system that utilizes double skins of profiled steel sheeting to form a sandwich construction. The work reported here involves the profiled concrete alone and provides information on the behavior of concrete walls that may be formed with a profiled surface. Model tests of 1/6 scale using microconcrete confirmed that the diagonal tension limit state should be the design criterion and the shear resistance of the profiled panels can be derived from its equivalent plain concrete panel. Compared to plain concrete panels, the state of stress within the panel and its boundaries is changed due to profile geometry. It has been found that a reduction factor may be introduced in the design equation to take into account the effect of hysteretic application of load. Finite-element simulation of the profiled panels was found to be good enough to predict the precracking behavior.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Balakrishnan, S., and Murray, D. W.(1988). “Strength of reinforced concrete panels.”Can. J. Civ. Engrg., Ottawa, Canada, 15, 900–911.
2.
Davies, J. M., and Fisher, J. (1979). “The diaphragm action of composite slabs.”Proc., Instn. of Civ. Engrs., London, U.K., 67(Part 2), 891–906.
3.
Easterling, W. S., and Porter, M. L.(1994a). “Steel-deck-reinforced concrete diaphragms. I.”J. Struct. Engrg., ASCE, 120(2), 560–576.
4.
Easterling, W. S., and Porter, M. L.(1994b). “Steel-deck-reinforced concrete diaphragms. II.”J. Struct. Engrg., ASCE, 120(2), 577–596.
5.
Hossain, K. M. A., and Wright, H. D. (1994). “Use of micro-concrete to simulate in-plane shear.”Nat. Res. Workshop on Cement and Concrete, Centre of Cement and Concrete, University of Sheffield, Sheffield, U.K., 11–12.
6.
Hossain, K. M. A., and Wright, H. D. (1995). “Composite walling with special reference to the stabilisation of building frames.”Proc., Nordic Steel Constr. Conf., 531–538.
7.
Hossain, K. M. A. (1995). “In-plane shear behaviour of composite walling with profiled steel sheeting,” PhD thesis, University of Strathclyde, Glasgow, U.K.
8.
Kupfer, H. B., and Gerstle, K. H.(1973). “Behavior of concrete under biaxial stresses.”J. Engrg. Mech. Div., ASCE, 99(4), 853–866.
9.
Luttrell, L. D. (1971). “Shear diaphragm with light weight concrete fill.”Proc., 1st Speciality Conf. on Cold-Formed Steel Struct., University of Missouri at Rolla, Rolla, Mo., 111–117.
10.
Mattock, A. H. (1974). “Shear transfer in concrete having reinforcement at an angle to shear plane, in shear in reinforced concrete.”Proc., Shear Symp., ACI Spec. Publ. SP-42, Vol. 1, American Concrete Institute, Detroit, Mich., 17–42.
11.
Pauly, T., and Loeber, P. I. (1974). “Shear transfer by aggregate interlock, in shear in reinforced concrete.”Proc., Shear Symp., ACI Spec. Publ. SP-42, Vol. 1, American Concrete Institute, Detroit, Mich., 1–15.
12.
Regan, P. E.(1969). “Shear in reinforced concrete beams.”Mag. Concrete Res., 21(66), 31–42.
13.
Sommerville, G., Roll, F., and Caldwell, J. A. D. (1965). “Tests on one-twelfth scale Mancunianway.”Tech. Rep. TRA/394, Cement and Concrete Association, London, U.K.
14.
Vecchio, F., and Collins, M. P.(1986). “Modified compression field theory for reinforced concrete elements subjected to shear.”ACI J., Proc., 83(2), 219–231.
15.
Vecchio, F., and Nieto, M.(1991). “Shear-friction tests on reinforced concrete panels.”ACI J., 88, 371–379.
16.
Waldron, P., and Perry, S. H. (1980). “Small scale micro-concrete control specimens.”Reinforced and prestressed micro-concrete models, F. K. Garas and G. S. T. Armer, eds., The Construction Press, Lancaster, Pa., 261–276.
17.
Waldron, P., Pinkey, M. W., and Perry, S. H. (1980). “The construction of a 1/12th scale prestressed concrete bifurcated bridge model.”Reinforced and prestressed micro-concrete models, F. K. Garas and G. S. T. Armer, eds., The Construction Press, Lancaster, Pa., 39–52.
18.
White, R. N., Sabnis, J. M., and Harries, H. G. (1966). “Small scale direct models of reinforced and prestressed concrete structures.”Rep. No. 326, Dept. of Struct. Engrg., School of Civ. Engrg., Cornell University, Ithaca, N.Y.
19.
Wright, H. D., Hossain, K. M. A., and Gallocher, S. C. (1994). “Composite walls as shear elements in tall structures.”Proc., ASCE Struct. Congr. XII, ASCE, 140–145.
Information & Authors
Information
Published In
Copyright
Copyright © 1998 American Society of Civil Engineers.
History
Published online: Apr 1, 1998
Published in print: Apr 1998
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.