Cyclic Test of Four-Story Steel Plate Shear Wall
Publication: Journal of Structural Engineering
Volume 124, Issue 2
Abstract
A large-scale, four-story, single bay steel plate shear wall specimen with unstiffened panels was tested using controlled cyclic loading to determine its behavior under an idealized severe earthquake event. The shear wall had moment-resisting beam-to-column connections, resulting in a lateral load-resisting system that possesses an inherent redundancy. Gravity loads were applied at the top of the wall and equal horizontal loads were applied at the four floor levels. The specimen endured 30 cycles of loading during the test, of which 20 cycles were in the inelastic range. Prior to failure of the specimen, the deflection reached in the lowest story was nine times the yield deflection. The test specimen proved to be initially very stiff, showed excellent ductility and energy dissipation characteristics, and exhibited stable behavior at very large deformations and after many cycles of loading. A description of the test setup, loading procedures, and specimen behavior is presented.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Blodgett, O. W. (1994). “Structural details to increase ductility of connections.”Proc., AISC Nat. Steel Constr. Conf., American Institute of Steel Construction (AISC), Inc., Chicago, Ill., 2-1–2-22.
2.
Caccese, V., Elgaaly, M., and Chen, R.(1993). “Experimental study of thin steel-plate shear walls under cyclic load.”J. Struct. Engrg, ASCE, 119(2), 573–587.
3.
Derecho, A. T., Iqbal, M., Fintel, M., and Corley, W. G. (1980). “Loading history for use in quasi-static simulated earthquake loading tests.”ACI Publ. SP63, Reinforced Concrete Structures Subjected to Wind and Earthquake Forces, American Concrete Institute, 329–356.
4.
Driver, R. G., Kulak, G. L., Elwi, A. E., and Kennedy, D. J. L.(1998). “FE and Simplified Models of steel plate shear wall.”J. Struct. Engrg., ASCE, 124(2), 121–130.
5.
Driver, R. G., Kulak, G. L., Kennedy, D. J. L., and Elwi, A. E. (1997). “Seismic behaviour of steel plate shear walls.”Struct. Engrg. Rep. 215, Dept. of Civ. and Envir. Engrg., University of Alberta, Edmonton, Alta., Canada.
6.
Elgaaly, M., and Caccese, V. (1990). “Steel plate shear walls.”Proc., AISC Nat. Steel Constr Conf., American Institute of Steel Construction (AISC), Inc., Chicago, Ill. 4-1–4-28.
7.
Elgaaly, M., Caccese, V., and Du, C.(1993). “Postbuckling behavior of steel-plate shear walls under cyclic loads.”J. Struct. Engrg., ASCE, 119(2), 588–605.
8.
Engelhardt, M. D., and Sabol, T. A. (1994). “Testing of welded steel moment connections in response to the Northridge earthquake.”Progress Rep. to the AISC Advisory Subcommittee on Special Moment Resisting Frame Res., Northridge Steel Update I, American Institute of Steel Construction (AISC), Inc., Chicago, Ill.
9.
“Guidelines for cyclic seismic testing of components of steel structures.” (1992). Rep. No. 24, Applied Technology Council, Redwood City, Calif.
10.
“Interim guidelines: evaluation, repair, modification and design of welded steel moment frame structures (SAC Joint Venture).” (1995). Publ. No. 267, Federal Emergency Management Agency, Washington, D.C.
11.
Kennedy, D. J. L., Kulak, G. L., and Driver, R. G.(1994). “Discussion of `Postbuckling behavior of steel-plate shear walls under cyclic loads,' by M. Elgaaly, V. Caccese, and C. Du.”J. Struct. Engrg., ASCE, 120(7), 2250–2251.
12.
Kulak, G. L., Kennedy, D. J. L., and Driver, R. G.(1994). “Discussion of `Experimental study of thin steel-plate shear walls under cyclic load,' by V. Caccese, M. Elgaaly, and R. Chen.”J. Struct. Engrg., ASCE, 120(10), 3072–3073.
13.
“Limit states design of steel structures.” (1994). CAN/CSA-S16.1-94, Canadian Standards Association, Rexdale, Ont., Canada.
14.
LRFD bridge design specifications—SI units. (1994). 1st Ed., American Association of State Highway and Transportation Officials, Washington, D.C.
15.
National building code of Canada. (1995). National Research Council of Canada, Ottawa, Ont., Canada.
16.
NEHRP recommended provisions for seismic regulations for new buildings. (1994). Federal Emergency Management Agency, Washington, D.C.
17.
Popov, E. P.(1980). “Seismic behavior of structural subassemblages.”J. Struct. Div., ASCE, 106(7), 1451–1474.
18.
Specification for structural steel buildings (LRFD). (1993). American Institute of Steel Construction (AISC), Inc., Chicago, Ill.
19.
“Structural quality steels.” (1992). CAN/CSA-G40.21-92, Canadian Standards Association, Rexdale, Ont., Canada.
20.
Takahashi, Y., Takemoto, Y., Takeda, T., and Takagi, M. (1973). “Experimental study on thin steel shear walls and particular bracings under alternative horizontal load.”Preliminary Rep., IABSE Symp. on Resistance and Ultimate Deformability of Struct. Acted on by Well-Defined Repeated Loads, International Association for Bridge and Structural Engineering, Lisbon, Portugal, 185–191.
21.
Thorburn, L. J., Kulak, G. L., and Montgomery, C. J. (1983). “Analysis of steel plate shear walls.”Struct. Engrg. Rep. No. 107, Dept. of Civ. Engrg., University of Alberta, Edmonton, Alta., Canada.
22.
Timler, P. A., and Kulak, G. L. (1983). “Experimental study of steel plate shear walls.”Struct. Engrg. Rep. No. 114, Dept. of Civ. Engrg., University of Alberta, Edmonton, Alta., Canada.
23.
Tromposch, E. W., and Kulak, G. L. (1987). “Cyclic and static behaviour of thin panel steel plate shear walls.”Struct. Engrg. Rep. No. 145, Dept. of Civ. Engrg., University of Alberta, Edmonton, Alta., Canada.
24.
Wagner, H. (1931). “Flat sheet metal girders with very thin webs, Part I—General theories and assumptions.”Tech. Memo. No. 604, National Advisory Committee for Aeronautics, Washington, D.C.
25.
Xue, M., and Lu, L.-W. (1994). “Interaction of steel plate shear panels with surrounding frame members.”Proc., Struct. Stability Res. Council Annu. Tech. Session, Bethlehem, Pa., 339–354.
26.
Yang, T.-S., and Popov, E. P. (1995). “Experimental and analytical studies of steel connections and energy dissipators.”Rep. No. UCB/EERC-95/13, Earthquake Engrg. Res. Ctr., University of California, Berkeley, Calif.
27.
Yarimci, E., Yura, J. A., and Lu, L.-W. (1966). “Techniques for testing structures permitted to sway.”Fritz Engrg. Lab. Rep. No. 273.40, Lehigh University, Bethlehem, Pa.
Information & Authors
Information
Published In
Copyright
Copyright © 1998 American Society of Civil Engineers.
History
Published online: Feb 1, 1998
Published in print: Feb 1998
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.