Static and Dynamic Behavior of Concrete Lift Joint Interfaces
Publication: Journal of Structural Engineering
Volume 124, Issue 12
Abstract
Displacement controlled shear tests on concrete lift joint specimens with different surface preparations are conducted to compare dynamic sliding joint behavior with the static behavior. Experimental results indicate that the coefficient of friction decreases with the increase in normal load, under both static and dynamic shear. The shear strength is dependent on surface preparation. Monolithic specimens and water-blasted joints show higher shear strengths than untreated joints and plane independent joint surfaces. No strength degradation is noticeable under dynamic sliding shear tests since hysteresis loops are very stable. No dependency of shear strength on frequency content of the imposed shear displacements is observed. An empirical lift joint constitutive model is developed as a function of a basic friction coefficient and a roughness friction coefficient that is dependent upon the type of surface preparation. The proposed lift joint constitutive model is used to study the seismic sliding response of a 90-m concrete gravity dam.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
“Building code requirements for reinforced concrete.” (1989). ACI 318-89, Am. Concrete Inst., Detroit, Mich.
2.
“Dam safety guidelines.” (1995). Can. Dam Safety Assn., Edmonton, AB, Canada.
3.
“Earthquake engineering for concrete dams: Design, performance and research needs.” (1990). National Academy Press, Washington, D.C., 143.
4.
Fronteddu, L. (1994). “Weak planes in dams, a literature review.”Rep. No. EPM/GCS-1994-18, Dept. of Civ. Engrg., École Polytechnique de Montreal, Montreal, PQ, Canada, 226.
5.
Fronteddu, L. (1997). “Experimental and numerical evaluation of the effects of concrete lift joints on static and seismic response of gravity dams,” PhD thesis, Dept. of Civ. Engrg., École Polytechnique de Montreal, Univ. of Montreal, Montreal, PQ, Canada.
6.
Léger, P., and Leclerc, M.(1996). “Evaluation of earthquake ground motions to predict cracking response of gravity dams.”Engrg. Struct., 18(3), 227–239.
7.
Lo, K. Y., Ogawa, T., Lukajic, B., Smith, G. F., and Dupac, D. D. (1991). “Measurements of strength parameters of concrete-rock contact at the dam foundation interface.”Geotech. Testing J., American Society for Testing and Materials, 14(4), 383–394. Manual of dam construction . (1990). Bull. 59, Int. Commission on Large Dams, Paris, France, 45.
8.
Patton, F. D.(1966). “Multiple modes of shear failure in rock.”Proc., 1st Congr. of Int. Soc. of Rock Mech., Laboratorio Nacional de Engenharia Civil, ed., Bertrand Irmaos Lda, Lisbon, Portugal, 1, 509–513.
9.
Saouma, V. E., Broz, J. J., Brühwiler, E., and Boggs, H. L.(1991). “Effect of aggregate and specimen size on fracture properties of dam concrete.”J. Mat. in Civ. Engrg., ASCE, 3(3), 204–218.
10.
Tassios, T. P., and Vintzèleou, E. N.(1987). “Concrete-to-concrete friction.”J. Struct. Engrg., ASCE, 113(4), 832–849.
11.
Tschegg, E. K., Tan, D. M., Kirchner, H. O. K., and Stanzi, S. E.(1993). “Interfacial and subinterfacial fracture in concrete.”Acta Metallurgica et Materialia, Elsevier, 41(2), 569–576.
12.
Walraven, J. C.(1981). “Fundamental analysis of aggregate interlock.”J. Struct. Engrg., ASCE, 107(11), 2245–2270.
13.
Walraven, J. C.(1994). “Rough cracks subjected to earthquake loading.”J. Struct. Engrg., ASCE, 120(5), 1510–1524.
Information & Authors
Information
Published In
Copyright
Copyright © 1998 American Society of Civil Engineers.
History
Published online: Dec 1, 1998
Published in print: Dec 1998
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.