Tension Stiffening Behavior of Reinforced Masonry
Publication: Journal of Structural Engineering
Volume 123, Issue 5
Abstract
The tensile behavior of reinforced concrete and clay unit masonry was studied by conducting a series of 33 direct tension tests on instrumented specimens. The effect of the steel reinforcement ratio was the principal variable considered. Reinforcing steel bars varied from no. 4 to no. 11 bars, while masonry unit widths varied from 90 to 290 mm. The measured tensile stress-strain curve permitted determination of the decrease in the tension stiffening behavior as a function of the cracking strain. All specimens were strained to levels far in excess of those permitted by design codes without suffering tensile bar failure. Initial behavior was governed by elastic properties. After cracking, a rapid decrease in effective stiffness was observed with the stiffness reducing to that of the reinforcing steel at a strain of approximately four times the cracking strain. This observation is significantly different from that reported for reinforced concrete. Examination of the stress-strain curve after yield showed a very strong influence of the reinforcing ratio on the shape of the stress-strain curve with lower steel ratios resulting in decreased ductility.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Baynit, R. A. (1990). “Bond and development length in reinforced concrete block masonry,” master's of engineering thesis, Carleton Univ., Ottawa, Ontario, Canada.
2.
Cheema, T. S., and Klingner, R. E.(1985). “Tensile anchorage behavior of deformed reinforcement in grouted concrete masonry.”ACI J., 82(3), 372–380.
3.
Ewing, R. D., El-Mustapha, A. M., and Kariotis, J. C. (1987). “FEM/I, a finite element computer program for the nonlinear static analysis of reinforced masonry building components.” Draft Rep. (Revised June 1989), EKEH—Joint Venture, Rancho Palos Verdes, Calif.
4.
Gilbert, R. I., and Warner, R. F.(1978). “Tension stiffening in reinforced concrete slabs.”Proc., ASCE, New York, N.Y., 104(12), 1885–1900.
5.
Hammons, M. I., Atkinson, R. H., Schuller, M. P., and Tikalsky, P. J. (1994). “Masonry research for limit states design.”U.S. Army Corps of Engrs. Wtrwy. Experiment Station Rep. CPAR-SL-94-1, Vicksburg, Miss.
6.
Horton, R. T., and Tadros, M. K.(1990). “Deflection of reinforced concrete masonry members.”ACI Struct. J., 87(4), 453–463.
7.
Massicotte, B., Elwi, A. E., and MacGregor, J. G.(1990). “Tension-stiffening model for planar reinforced concrete members.”J. Struct. Engrg., ASCE, 116(11), 3039–3058.
8.
Matsumura, A. (1990). “Test on lap splices of relatively large size bars in masonry.”Proc., 6th Meeting of U.S.-Japan Joint Tech. Coordinating Com. on Masonry Res., Atkinson-Noland, Boulder, Colo.
9.
Nunn, R. O. (1980). “Planar mechanics of fully grouted concrete masonry.”Rep. UCSD/AMES/TR-80/001, Univ. of California at San Diego, Dept. of Appl. Mech. and Engrg. Sci.
10.
Prakhya, G. K. V., and Morley, C. T.(1990). “Tension-stiffening and moment-curvature relations of reinforced concrete elements.”ACI Struct. J., 87(5), 597–605.
11.
Seible, F., LaRovere, H. L., and Kingsley, G. R. (1989). “Nonlinear analysis of reinforced masonry shear wall structure—monotonic loading.”The Masonry Soc. J., (9)1, 60–69.
12.
Vecchio, F., and Collins, M. P. (1982). “The response of reinforced concrete to in-plane shear and normal stresses.”Rep., Dept. of Civ. Engrg., Univ. of Toronto, Ontario, Canada.
13.
Watanabe, M. (1985). “Bond and anchorage of reinforcement in masonry.”Proc., 1st Joint Tech. Coordinating Com. on Masonry Res., U.S.-Japan Coordinating Program for Masonry Build. Res., Atkinson-Noland, Boulder, Colo.
14.
Williams, S. (1986). “Tests on large reinforced concrete elements subjected to direct tension.”Tech. Rep. 562, Cement and Concrete Assn., London.
Information & Authors
Information
Published In
Copyright
Copyright © 1997 American Society of Civil Engineers.
History
Published online: May 1, 1997
Published in print: May 1997
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.