Study of Moment Redistribution in Prestressed Concrete Beams
Publication: Journal of Structural Engineering
Volume 123, Issue 5
Abstract
This paper describes an investigation into the redistribution of moments in certain composite concrete beams. Seven two-span beams 6.2 m long were constructed and tested by means of applying two point loads at midspans. Each beam comprised two precast beams made continuous by a top flange cast “in situ.” Since the term “redistribution of moments” is normally used in two different meanings (in research papers or in codes of practice), the concept of degree of redistribution is explained. A brief bibliography review presents the main research advances in this subject, and the contradiction between the results is significant in some cases. The experimental program is presented as well as the geometric and material properties of the test beams. The main results obtained from tests are presented from zero loading up to failure. The ultimate loads obtained from the tests are compared with theoretical ones considering both plastic and elastic behavior. Conclusions from the results are presented.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
American Concrete Institute (ACI). (1989). “Part 3: use of concrete in buildings—design, specification and related topics.”ACI manual of concrete practice 1989, Detroit, Mich.
2.
Arenas, J. J. (1986). “Continuous partially prestressed structures: European perspective.”Partial prestressing, from theory to practice, Vol. I, Survey Reports, NATO ASI Series, Martinus Nijhoff Publishers, Boston, Mass., 257–287.
3.
Baker, A. L. L. (1949). “A plastic theory of design for ordinary reinforced and prestressed concrete including moment redistribution in continuous members.”Mag. Concrete Res., Slough, England, (2), 57–66.
4.
Baker, A. L. L. (1951). “Recent research in reinforced concrete and its application to design.”J. Instn. of Civ. Engrs., London, England, (35), 262–329.
5.
Baker, A. L. L. (1953). “Further research in reinforced concrete and its application to ultimate load design.”Proc., Instn. of Civ. Engrs., London, England, (2), 269–307.
6.
Baker, A. L. L., and Amarakone, A. M. N. (1964). “Inelastic hyperstatic frames analysis.”Proc., Int. Symp. on Flexural Mech. of Reinforced Concrete, Miami, Florida, November, 85–142.
7.
Bennett, E. W. (1955). “Discussion of section IIIa.”Proc., 2nd Congr. of the Fédération Internationale de la Précontrainte, Amsterdam, Holland, 645–646.
8.
Bennett, E. W., Cooke, N., and Naughton, L. P.(1967). “Deformation of continuous prestressed concrete beams and its effect on the ultimate load.”Proc., Instn. of Civ. Engrs., Institution of Civil Engineers, London, England, 37, 57–74.
9.
Cohn, M. Z. (1986). “Continuity in prestressed concrete partial prestressing.”Partial prestressing, from theory to practice, Vol. I, Survey Reports, NATO ASI Series, Martinus Nijhoff Publishers, Boston, Mass., 189–256.
10.
Cohn, M. Z., and Petcu, V. A. (1963). “Moment redistribution and rotation capacity of plastic hinges in redundant reinforced concrete beams.”Indian Concrete J., (August), India, 282–290.
11.
Comité Européen de Normalisation (CEN). (1992). “Eurocode 2—design of concrete structures.”Rep., ENV 1992-1-1:1992, Brussels, Belgium.
12.
Comité Euro-International du Béton (CEB). (1991). “CEB-FIP model code 1990.”Bull. d' Information N°204, Lausanne, Switzerland.
13.
Cooke, N. (1965). “The redistribution of bending moments in continuous prestressed concrete beams,” PhD thesis, Dept. of Civ. Engrg., Univ. of Leeds, Leeds, England.
14.
Guyon, Y. (1955). “General report on moment distribution in statically indeterminate prestressed structures beyond the elastic phase.”Rep., 2nd Congr. of the Fédération Internationale de la Précontrainte, Amsterdam, Holland, 585–598.
15.
Lopes, S. M. R. (1990). “Moment redistribution in partially prestressed composite concrete beams,” PhD thesis, Dept. of Civ. Engrg., Univ. of Leeds, Leeds, England.
16.
Macchi, G. (1979). “Limit states design for reinforced and prestressed concrete–CEB approach.”Concrete Des.: U.S. and Eur. Practices ACI-CEB-PCI-FIP Symp., 1976 ACI Annu. Convention, ACI Publication SP-59, Detroit, Mich., 51–69.
17.
Mallick, S. K.(1962). “Redistribution of moments in two-span prestressed concrete beams.”Mag. Concrete Res., Slough, England, 14(42), 171–183.
18.
Mattock, A. H. (1983). “Secondary moments and moment redistribution in ACI 318-77 code.”Int. Symp. on Nonlinearity and Continuity in Prestressed Concrete, Vol. 3, Univ. of Waterloo, Waterloo, Ontario, Canada, 27–48.
19.
Moucessian, A. (1986). “Nonlinearity and continuity in prestressed concrete beams,” PhD thesis, Queen's Univ. at Kinston, Kinston, Canada.
20.
Priestley, M. J. N., and Park, R.(1972). “Moment redistribution in continuous prestressed concrete beams.”Mag. Concrete Res., Slough, England, 24(80), 157–175.
21.
Sallan, A. J. S. (1984). “Dimensionamiento de Vigas Continuas de Hormigon Parcialmente Pretensado por Condiciones Estritas de Seguridad a Rotura (Design of Partially Prestressed Concrete Continuous Beams Considering Only Safety Conditions at the Failure),” PhD thesis, Univ. of Santander, Santander, Spain (in Spanish).
22.
Tíchy, M., and Rákosník, J. (1977). Plastic analysis of concrete frames (with particular reference to limit states design). Collet (Publishers) Ltd., London, England.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 123 • Issue 5 • May 1997
Pages: 561 - 566
Copyright
Copyright © 1997 American Society of Civil Engineers.
History
Published online: May 1, 1997
Published in print: May 1997
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.