Plastic Buckling Approximation for Transition Ringbeams in Steel Silos
Publication: Journal of Structural Engineering
Volume 123, Issue 12
Abstract
An annular plate ringbeam at the transition junction of a uniformly-supported steel silo or tank is subject to a large circumferential compressive force that is derived from the radial component of the meridional tension in the conical hopper. Under this compressive force, the ringbeam may fail in one of several possible modes, including out-of-plane buckling. This paper presents an investigation into the effects of various factors on the plastic out-of-plane buckling behavior and strength of this ringbeam, leading to the eventual development of a simple plastic buckling approximation for design use. The application of the proposed method is demonstrated through an example.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Galletly, G. D. (1985). “Torispherical shells.”Shell structures: stability and strength, R. Narayanan, ed., Elsevier Applied Science, New York, N.Y.
2.
Galletly, G. D., and Blachut, J. (1985). “Torispherical shells under internal pressure-failure due to asymmetric buckling or axisymmetric yielding.”Proc., Inst. of Mech. Engrs., 1999(C3), 225–228.
3.
Gaylord, E. H., and Gaylord, C. N. (1984). Design of steel bins for storage of bulk solids. Prentice Hall, Inc., Englewood Cliffs, N.J.
4.
Greiner, R. (1991). “Elastic plastic buckling at cone cylinder junctions of silos.”Buckling of shell structures on land, in the sea and in the air, J. F. Jullien, ed., Elsevier Applied Science, New York, N.Y.
5.
Janssen, H. A.(1895). “Versuche uber getreidedruck in silozellen.”Zeitschrift des vareines Deutscher Ingenieure, 29(35), 1045–1049.
6.
Jumikis, P. T. (1987). “Stability problems in silo structures,” PhD thesis, School of Civ. and Min. Engrg., Univ. of Sydney, Australia.
7.
Jumikis, P. T., and Rotter, J. M. (1983). “Buckling of simple ringbeams for bins and tanks.”Proc., Int. Conf. on Bulk Mat. Storage, Handling and Transp., Inst. of Engrs., Newcastle, Australia, Aug., 323–328.
8.
Rotter, J. M. (1985). “Analysis and design of ringbeams.”Design of steel bins for the storage of bulk solids, School of Civ. and Min. Engrg., Univ. of Sydney, Australia., March, 164–183.
9.
Rotter, J. M. (1987). “The buckling and plastic collapse of ring stiffeners at cone/cylinder junctions.”Proc., Int. Colloquium on the Stability of Plate and Shell Struct., Gent, Belgium, April, ECCS, 449–456.
10.
Rotter, J. M. (1996). “Shell structures: design standards, recent progress and unsolved problems.”Advances in steel structures, S. L. Chan and J. G. Teng, eds., Elsevier Science Publishing Co. Inc., New York, N.Y.
11.
Sharma, U. C., Rotter, J. M., and Jumikis, P. T. (1987). “Shell restraint to ringbeam buckling in elevated steel silos.”Proc., 1st Nat. Struct. Engrg. Conf., Inst. of Engrs., Australia, Aug., 604–609.
12.
Teng, J. G.(1994). “Cone-cylinder intersection under internal pressure: axisymmetric failure.”J. Engrg. Mech., ASCE, 120(9), 1896–1912.
13.
Teng, J. G.(1996). “Buckling of thin shells: recent advances and trends.”Appl. Mech. Rev., 49(4), 263–274.
14.
Teng, J. G. (1997). “On the buckling strength of ringbeams in steel silos.” Presented at the Int. Conf. on Carrying Capacity of Steel Shell Struct., Oct. 1–3, 1997, Brno, Czech Republic.
15.
Teng, J. G., and Rotter, J. M.(1989). “Non-symmetric bifurcation of geometrically non-linear elastic-plastic axisymmetric shells subject to combined loads including torsion.”Comp. and Struct., 32(2), 453–477.
16.
Teng, J. G., and Rotter, J. M.(1991a). “The collapse behavior and strength of steel silo junctions-Parts I and II.”J. Struct. Engrg., ASCE, 117(12), 3587–3622.
17.
Teng, J. G., and Rotter, J. M.(1991b). “Plastic buckling of rings at steel silo transition junctions.”J. Constr. Steel Res., 19, 1–18.
18.
Teng, J. G., and Rotter, J. M.(1991c). “Strength of welded steel silo hoppers under filling and flow pressures.”J. Struct. Engrg., ASCE, 117(9), 2567–2583.
19.
Trahair, N. S., Abel, A., Ansourian, P., Irvine, H. M., and Rotter, J. M. (1983). “Structural design of steel bins for bulk solids.” Australian Inst. of Steel Construct., Sydney.
20.
Walker, D. M.(1966). “An approximate theory for pressure and arching in hoppers.”Chemical Engrg. Sci., 21, 975–997.
21.
Wozniak, R. S. (1979). “Steel tanks.”Structural engineering handbook, 2nd Ed., Sect. 23, E. H. Gaylord and C. N. Gaylord, eds., McGraw-Hill Inc., New York, N.Y.
Information & Authors
Information
Published In
Copyright
Copyright © 1997 American Society of Civil Engineers.
History
Published online: Dec 1, 1997
Published in print: Dec 1997
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.