Nonlinear Finite-Element Model of Hollow Masonry
Publication: Journal of Structural Engineering
Volume 122, Issue 6
Abstract
A nonlinear elastoplastic finite-element (FE) model for face-shell-bedded hollow masonry using isoparametric shell elements has been developed. The nonlinear behavior of the masonry in compression due to progressive cracking, and geometric and material nonlinearities is considered in the model. Details of the elastoplastic constitutive model and failure criteria for both blocks and mortar joints are presented. Results from a simulated test of a three-block-high prism are given in the form of stress, strain, and displacement plots. The behavior of the model is compared to known experimental behavior. The methodology, when combined with the substructuring technique, will allow analysis of substantially larger walls than would the more typical full three-dimensional (3D) analysis.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Ali, S. (1987). “Concentrated loads on solid masonry,” PhD thesis, Civ. Engrg. Dept., Univ. of Newcastle, Newcastle, Australia.
2.
Ali, S., and Page, A. W. (1986). “The use of discrete cracking modelling in the finite element analysis of concentrated loads on masonry.”Proc., 10th Australian Conf. on Mech. of Struct. and Mat., Civ. Engrg. Dept., Univ. of Adelaide, Australia, Vol. 1, 199–204.
3.
Ali, S., Page, A. W., and Kleeman, P. W. (1980). “Non-linear finite element model for concrete masonry with particular reference to concentrated load.”Proc., 4th Can. Masonry Symp., Civ. Engrg. Dept., Univ. of New Brunswick, Fredericton, N.B., Canada, Vol. 1, 137–148.
4.
Becica, I. J., and Harris, H. G. (1983). “Behaviour of hollow concrete masonry prisms under axial loads and bending.”The Masonry Soc. J., T1–T26.
5.
Crissfield, M. A. (1984). “Overcoming limit points with material softening and strain localization.”Numerical methods for non-linear problems, Vol. 2, Taylor et al., eds., Pinerdge Press, Swansea, Wales, 244–277.
6.
Crissfield, M. A. (1986). “Snap through and snap back response on concrete structures and danger of under integration.”Int. J. Numer. Methods in Engrg., Vol. 22, 751–767.
7.
Drucker, D. C. (1959). “A definition of stable inelastic material.”J. Appl. Mech., Vol. 26, 157–165.
8.
Drucker, D. C., and Prager, W.(1959). “Soil mechanics and plastic analysis or limit design.”J. Appl. Math., 10(2), 101–106.
9.
Fattal, S. G., and Cattaneo. L. E. (1973). “Structural performance of masonry walls under compression and flexure.”Build. Sci. Ser., Nat. Bureau of Standards, Gaithersburg, Md.
10.
Hamid, A. A., and Chukwunenye. (1985). “Effect of type of mortar bedding on the behaviour of axially loaded hollow masonry prisms.”Proc., 3rd North Am. Conf., Constr. Res. Ctr., Civ. Engrg. Dept., Univ. of Texas, Arlington, Tex., 16.1–16.12.
11.
Hatzinikolas, M., Longworth, J., and Warwaruk, J. (1977). “Failure modes of eccentrically loaded concrete block masonry walls.”ACI J., 258–263.
12.
Hilsdorf, H. K. (1975). “Investigation into the failure mechanism of brick masonry loaded in axial compression.”Designing, engineering and construction with masonry products, Gulf Publishing Co., Houston, Tex.
13.
Hosny, A., Soliman, M. I., and Fouad, H. A. (1990). “Nonlinear finite element analysis of masonry walls.”Proc., CSCE Conf.
14.
Maksoud, A. A., and Drysdale, R. G. (1992). “Numerical modelling of masonry walls.”Proc., 6th Can. Masonry Symp., 801–811.
15.
Middleton, J., Pande, G. N., Liang, J. X., and Kralj, B. (1991). “Some recent advances in computer methods in structural masonry.”Computer methods in structural masonry; Proc., Int. Symp., 1–21.
16.
Page, A. W., and Shrive, N. G. (1990), “Concentrated loads on hollow concrete masonry.”ACI Struct. J., 436–444.
17.
Rahman, A. H. (1986). “Thermal stresses in intersecting masonry walls— a finite element study,” PhD thesis, Carleton Univ., Ottawa, Canada.
18.
Rahman, A. H., and Suter, G. T.(1993). “Non-linear finite element analysis of thermal stresses in intersecting masonry walls.”Masonry Int., 6(3), 96–102.
19.
Ramm, E. (1982). “The Riks/Weapner approach—an extension of the displacement control method in numerical analysis.”Recent advances in nonlinear computational mechanics, Hinton, E. et al., eds., Pineridge Press, Swansea, Wales, 63–86.
20.
Sayed-Ahmed, E. Y. (1994). “Non-linear finite element analysis of face-shell bedded hollow concrete masonry subject to concentrated loads,” PhD dissertation, Civ. Engrg. Dept., Univ. of Calgary, Calgary, Alta., Canada.
21.
Sayed-Ahmed, E. Y., and Shrive, N. G.(1996). “Design of face-shell bedded hollow masonry subject to concentrated loads.”Can. J. Civ. Engrg., Ottawa, Canada, 23(1), 98–106.
22.
Shrive, N. G.(1982). “The failure mechanism of face-shell bedded (ungrouted and unreinforced) masonry.”Int. J. of Masonry Constr., 2(3), 115–128.
23.
Xie, H., Page, A. W., and Kleeman, P. W. (1992). “An investigation of the compressive failure mechanism for face-shell bedded hollow masonry.”Proc., 6th Can. Masonry Symp., Civ. Engrg. Dept., Univ. of Saskatchewan, Saskatoon, Canada, 97–108.
Information & Authors
Information
Published In
Copyright
Copyright © 1996 American Society of Civil Engineers.
History
Published online: Jun 1, 1996
Published in print: Jun 1996
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.